Fujitsu 8000 SERIES user manual Turning On the Power, Turning on the power

Page 28

6 Turning On the Power

This section explains how to turn on the power.

■Notes on power-on

•If nothing is displayed on the screen, check if the display cable is properly connected.

•In the case that the screen is not displayed in the center, adjust it using the display.

•When the power-on self-test (POST) detects an error, an error message is displayed.

•When the power cable of the display is connected to the PC, the display power is turned on or off automatically when the PC power is turned on or off. Therefore, once the power switch on the display is pressed, subsequent operation is not necessary.

•The display power is automatically turned on each time the power switch on the PC is pressed as in Step 2 below. However, it is required to power on peripheral devices other than the display before powering on your PC.

•When the display power is not automatically turned on with the PC power, you are required to turn on it before turning on the PC.

•To turn off the PC power just after turning it on, wait until the OS starts and turn it off following the instructions described in “Turning Off the Power”.

■Turning on the power

WARNING

● Do not carry or subject the PC to shock or vibration while the PC is on. Otherwise, a fault may occur.

1Press the power switches on the display and other peripheral devices. At this time, nothing is displayed on the screen.

18

Image 28

Contents

Deskpower 8000 Series User’s Manual Declaration of ConformityImportant Safety Instructions Page Greetings Command entries Conventions used in this manualRepresenting keys and use thereof Representing buttonsPoint Help Conventions used in the text of the manualScreen display examples IllustrationsFujitsu Limited Manual configuration IntroductionContents Installing Expansion Cards Installing an Internal Hard DiskInstalling Other Devices ProblemsIntroduction Part Names and Functions Front of the PC unitHeadphone volume only for music CDs Floppy disk access lampHard disk access lamp Power lampBack of the PC unit LAN connector Connect a LAN cable Line OUT terminal CRT connectorInlet OutletInside the PC unit Power supply unit Internal hard disk bayDisplay card Expansion card slots Motherboard Keyboard PointCaps Lock/Alphanumeric key Ctrl control keyWindows key Alt keyUsing the mouse Using the mouse buttonsMouse Moving the mouseDouble-clicking PointingDragging ScrollingInstallation area InstallationExample of installation Connection Connect the power cable to the display Connect the power cable to the outlet Connect the keyboard Connect the display cable to the PC unit Connect the mouseConnect the LAN cable Connecting the power cable Page Turning On the Power Turning on the powerPress the power switch on the PC Turning Off the Power Turning off the powerFor Windows Me or 98 model For Windows NT modelResetting Resetting the PCHard resetting CDs Inserting or Removing CD Inserting a CDRemoving the CD Press the eject buttonInserting or removing a floppy disk Point Floppy DiskInserting a floppy disk Confirm that the floppy disk access lamp is off Removing the floppy diskHardware Before Installing a Peripheral Device What are peripheral devices?Page Location for installation File bay options Master and slave On standard modelsSlave Master Removing the Cover Removing the side and upper covers, and front panelRemove the side cover Remove the bracketPage Tilt the front panel toward you before pulling it up Increasing the Memory Capacity Applicable memory modules Location of memory modulesMemory module combinations Installing/removing memory modules Installing memory modules Remove the brackeReinstall the duct Reinstall the bracket Reinstall the side coverRemoving memory modules Insert a memory module into the slotInstalling Expansion Cards Installing an expansion card Applicable expansion cardsFix the expansion card with the one screw removed in Step Reinstall the bracket Installing a disk in the internal hard disk bay Installing an Internal Hard DiskSet the jumper switch Replace or install the internal hard disk Attach the brackets to the PC unitConnect the power cable Connect flat cablesInstalling a disk in the front access bay Installing Other Devices Installing front access bay optionsInstall a front access bay option on the PC unit CD-ROM Reinstall the front panel and upper and side covers Set the installed hard disks using Bios Setup Page Troubleshooting Problems Characters entered using the keyboard are not displayed Data cannot be read from the CD-ROM driveMouse cursor does not move Network connection cannot be establishedPage Technical Information Maintenance of the keyboard Maintenance of the HardwareMaintenance of CDs Maintenance of the mouse Remove the ball and clean with waterClean inside the mouse Remove the mouse bottom coverCleaning of the floppy disk drive Precautions on television/radio Precautions on PCPreventing Television or Radio Interference Security of the Case Engage a lock you prepared with the mounting bracketSpecifications of PC unit Hardware SpecificationsProduct name Point LAN adapter specifications Sound specificationsGraphical specifications LAN controller IntelConnector specifications CRT connectorLAN connector 100BASE-TX/10BASE-T Pin No Signal name DescriptionParallel connector Serial connectorKeyboard connector Mouse connectorUSB connector Other Precautions Power-saving function Windows 2000 modelsWhen using USB devices DisposalPrecautions on using display Replacement of displayUSB hub Windows 2000 models Addition of LAN adapterAcpi standby mode Windows 2000 models Index Parallel connector