Fujitsu 8000 SERIES user manual

Page 3

13.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance, indicating a need for service.

14.CAUTION. When replacing the battery, be sure to install it with the polarities in the correct position. There is a danger of explosion if the battery is replaced with an incorrect type or is mistreated. Do not recharge, disassemble or dispose of in fire. Replace only with the same or equivalent type recommeded by the manufacturer. Dispose of the used battery according to the manufacturer’s instructions.

15.Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It should be a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145 certified, rated 10A 250V minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).

Image 3 Contents
Declaration of Conformity Deskpower 8000 Series User’s ManualImportant Safety Instructions Page Greetings Representing buttons Command entriesConventions used in this manual Representing keys and use thereofIllustrations Point HelpConventions used in the text of the manual Screen display examplesFujitsu Limited Introduction Manual configurationContents Problems Installing Expansion CardsInstalling an Internal Hard Disk Installing Other DevicesIntroduction Front of the PC unit Part Names and FunctionsPower lamp Headphone volume only for music CDsFloppy disk access lamp Hard disk access lampBack of the PC unit Outlet LAN connector Connect a LAN cable Line OUT terminalCRT connector InletPower supply unit Internal hard disk bay Inside the PC unitDisplay card Expansion card slots Motherboard Point KeyboardAlt key Caps Lock/Alphanumeric keyCtrl control key Windows keyMoving the mouse Using the mouseUsing the mouse buttons MouseScrolling Double-clickingPointing DraggingInstallation Installation areaExample of installation Connection Connect the power cable to the outlet Connect the power cable to the displayConnect the keyboard Connect the mouse Connect the display cable to the PC unitConnect the LAN cable Connecting the power cable Page Turning on the power Turning On the PowerPress the power switch on the PC For Windows NT model Turning Off the PowerTurning off the power For Windows Me or 98 modelResetting the PC ResettingHard resetting CDs Press the eject button Inserting or Removing CDInserting a CD Removing the CDFloppy Disk Inserting or removing a floppy disk PointInserting a floppy disk Removing the floppy disk Confirm that the floppy disk access lamp is offHardware What are peripheral devices? Before Installing a Peripheral DevicePage Location for installation File bay options On standard models Master and slaveSlave Master Removing the side and upper covers, and front panel Removing the CoverRemove the bracket Remove the side coverPage Tilt the front panel toward you before pulling it up Increasing the Memory Capacity Location of memory modules Applicable memory modulesMemory module combinations Installing/removing memory modules Remove the bracke Installing memory modulesInsert a memory module into the slot Reinstall the ductReinstall the bracket Reinstall the side cover Removing memory modulesInstalling Expansion Cards Applicable expansion cards Installing an expansion cardFix the expansion card with the one screw removed in Step Reinstall the bracket Installing an Internal Hard Disk Installing a disk in the internal hard disk baySet the jumper switch Attach the brackets to the PC unit Replace or install the internal hard diskConnect flat cables Connect the power cableInstalling a disk in the front access bay Installing front access bay options Installing Other DevicesInstall a front access bay option on the PC unit CD-ROM Reinstall the front panel and upper and side covers Set the installed hard disks using Bios Setup Page Troubleshooting Problems Network connection cannot be established Characters entered using the keyboard are not displayedData cannot be read from the CD-ROM drive Mouse cursor does not movePage Technical Information Maintenance of the Hardware Maintenance of the keyboardMaintenance of CDs Remove the mouse bottom cover Maintenance of the mouseRemove the ball and clean with water Clean inside the mouseCleaning of the floppy disk drive Precautions on PC Precautions on television/radioPreventing Television or Radio Interference Engage a lock you prepared with the mounting bracket Security of the CaseHardware Specifications Specifications of PC unitProduct name Point LAN controller Intel LAN adapter specificationsSound specifications Graphical specificationsPin No Signal name Description Connector specificationsCRT connector LAN connector 100BASE-TX/10BASE-TSerial connector Parallel connectorMouse connector Keyboard connectorUSB connector Disposal Other PrecautionsPower-saving function Windows 2000 models When using USB devicesAddition of LAN adapter Precautions on using displayReplacement of display USB hub Windows 2000 modelsAcpi standby mode Windows 2000 models Index Parallel connector