Bush Hog manual Model 3860 QT Technical Specifications

Page 10

Model 3860 QT Technical Specifications

D

E

A

B

J C

G

F

H

D

E

J C

G

F

H

A.

Maximum Lift Height - Measured at Pivot Pin

. . . .176"

B.

Maximum Lift Height - Under Level Bucket . . . . . 170"

C.

Clearance with Attachment Dumped 45º . . . .

. . . 148"

D.

Reach at Maximum Height

. . . . 33”

E.

Maximum Dump Angle

. . . . 34°

F.

Reach with Bucket on Ground

. . . . 89”

G.

Maximum Rollback Angle

. . . . 19°

H.

Digging Depth

. . . . . 5”

J.

Overall Height in Carry Position

. . . . 81”

U.

Lift Capacity to Maximum Height - At Pivot Pin . .

4580 lbs.

V.

Lift Capacity to Maximum Height -

 

 

31.5” Forward of Pivot Pin

3680 lbs.

W. Lift Capacity to 59” Height - At Pivot Pin

7100 lbs.

X.

Lift Capacity to 59” Height -

 

 

31.5” Forward of Pivot Pin

4970 lbs.

Y.

Breakout Force - At Pivot Pin

8400 lbs.

Z.

Breakout Force - 31.5” Forward of Pivot Pin .

6050 lbs.

VV.

Rollback Force at Maximum Height -

 

 

31.5” Forward of Pivot Pin

7706lbs.

XX.

Rollback Force at 59” Height -

 

 

31.5” Forward of Pivot Pin

6787 lbs.

ZZ.

Rollback Force at Ground Level -

 

 

31.5” Forward of Pivot Pin

5250 lbs.

 

Raising Time - Ground Level to Full Height . .

5.7 sec.

 

Lowering Time - Full Height to Ground Level .

5.1 sec.

 

Bucket Dumping Time - Full Rollback

 

 

to Full Dump

3.3 sec.

 

Bucket Rollback Time - Full Dump

 

 

to Full Rollback

3.8 sec.

Specififications based on tractor system of 2800 psi hydraulic pres- sure and 28 gpm pump capacity. Specifications will vary slightly with different tractors.

SPECIFICATIONS BASED ON 1997 ASAE STANDARDS AND SUBJECT

TO CHANGE WITHOUT NOTICE

8

Image 10
Contents Bush HOG Congratulations Table of Contents 3860 QTThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Tractor Important Safety PrecautionsLoader Safety Precautions Operating the LoaderEMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsIntroduction Introduction and DescriptionDescription Model 3860 QT Technical Specifications Tractor Preparation Installation InstructionsInstallation Important NoticeFront Bracket Forward SideSubframe Crosstube Lift and Support ALL Loader COMPO- Nents Safely Torque IdentificationInitial Loader Operation PRE-OPERATION InstructionsTransmission Fluid External Loader AND/OR Tractor ValveFloat Position Bucket Level IndicatorNeutral Position Initial Loader OperationRemote Hoses Support Daily Checks MaintenanceLoader Lubrication Bucket Level Gauge ROD General SafetyOperating Instructions OperationFilling the Bucket Lifting the LoadLowering the Bucket Carrying the LoadDumping the Bucket Not this Do this Dump Lower LeverFloat Operating with Float ControlFloat Surface Material Loading from a Bank 3RD CUT , 4TH CUT, ETC Do this Peeling and ScrapingBackfilling Loading LOW Trucks or Spreaders from a PileSoil Pile Back GradingTroubleshooting Procedures Problem Possible Cause Remedy Setting recommendedDismounting the Loader Page Mounting the Loader Page Installation & Operation of Quick Draw Latch Attach Upper channel Weld-in center support Bucket or attachment Installing Bucket or Attachment to Quick Draw Latch Attach Page Removing Bucket or Attachment from Quick Draw Latch Attach Quick Draw Bucket Bucket AttachmentSingle Tine KIT Super Penetrator Bale Probe Attachment Manure Fork Attachment Dozer AttachmentOperating Instructions for Dismounting Dozer from Loader Pallet Fork Attachment Parking AnglesGrapple Attachment Page Operating Instructions Page Supplemental Instructions For Ford Genesis Special Safety Decals Decals Torque Specifications American