Bush Hog 3860 QT manual

Page 41

Figure 10

Ref. Qty. Description

12 Grapple Cylinder 2-1/2"

24 Fitting, 90° NPTF 1/2" x ORBM 3/4"

34 Clevis pin 5/16" x 2" Heat Treated for use on 1-1/8" pins

2 Clevis pin 3/8" x 2-1/4"

for use on 1-5/16" pins.

46 Cotter Pin 1/8" x 1"

51 Hose 3/8" x 47.72" Top Left

61 Hose 3/8" x 27.48" Top Right

71 Hose 3/8" x 42.73" Bottom Left

81 Hose 3/8" x 22.98" Bottom Right

91 Quick Coupler Mount

101 Hex Bolt 3/8"-16NC x 3-1/2" Grade 5

112 Flatwasher 3/8"

Ref.	Qty.	Description
12	2	Hex Nut 3/8" Nylon Lock
13	1	Hex Bolt 3/8"-16NC x 1-3/4"
		Pin On Bucket only, or
	1	Weld-on Stud

Quick Draw Bucket only.

141 Hose Clamp Plastic 5/8 x 5/8

151 Hose Bar Support 3/16" x 1" x 2-1/2"

161 Quick Coupler Male ORBF 3/4"

171 Quick Coupler Female ORBF 3/4"

181 Quick Coupler Dust Plug

192 Bulkhead O-Ring 3/4"

202 Fitting Str. Bulkhead JIC M 3/4"-16

212 Bulkhead Nut 3/4"-16

222 Fitting Tee JIC M-M-F 3/4"-16

39

Image 41

Contents Bush HOG Congratulations 3860 QT Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not ApplyDealer Preparation Check List Loader Important Safety PrecautionsTractor Operating the Loader Safety PrecautionsEmployee Tractor Operating Instructions EMPLOYERS, Employees and OperationsDescription Introduction and DescriptionIntroduction Model 3860 QT Technical Specifications Installation Installation InstructionsTractor Preparation Important NoticeSubframe Crosstube Forward SideFront Bracket Torque Identification Lift and Support ALL Loader COMPO- Nents SafelyTransmission Fluid PRE-OPERATION InstructionsInitial Loader Operation External Loader AND/OR Tractor ValveNeutral Position Bucket Level IndicatorFloat Position Initial Loader OperationRemote Hoses Support Loader Lubrication MaintenanceDaily Checks Operating Instructions General SafetyBucket Level Gauge ROD OperationLifting the Load Filling the BucketDumping the Bucket Carrying the LoadLowering the Bucket Not this Do this Dump Lower LeverFloat Surface Material Loading from a Bank Operating with Float ControlFloat Backfilling Peeling and Scraping3RD CUT , 4TH CUT, ETC Do this Loading LOW Trucks or Spreaders from a PileBack Grading Soil PileSetting recommended Troubleshooting Procedures Problem Possible Cause RemedyDismounting the Loader Page Mounting the Loader Page Installation & Operation of Quick Draw Latch Attach Upper channel Weld-in center support Bucket or attachment Installing Bucket or Attachment to Quick Draw Latch Attach Page Removing Bucket or Attachment from Quick Draw Latch Attach Single Tine KIT Bucket AttachmentQuick Draw Bucket Super Penetrator Bale Probe Attachment Operating Instructions for Dismounting Dozer from Loader Dozer AttachmentManure Fork Attachment Parking Angles Pallet Fork AttachmentGrapple Attachment Page Operating Instructions Page Supplemental Instructions For Ford Genesis Special Safety Decals Decals American Torque Specifications