Bush Hog 3860 QT manual Bucket Attachment, Quick Draw Bucket, Single Tine KIT

Page 34

11. BUCKET ATTACHMENT

QUICK DRAW BUCKET

IMPORTANT: Refer to pages 29 & 30 for instruc- tions concerning Installing Attachment to Quick Draw Latch Attach.

IMPORTANT: Refer to page 31 for instructions concerning Removing Attachment from Quick Draw Latch Attach.

Quick draw buckets are available as follows.

72 inch, 84 inch, and 96 inch wide for Bush Hog 3860 Loaders.

These buckets utilize a replaceable weld-on cutting edge, and are pre-punched for tines.

Heavy duty/high capacity quick draw buckets are available as follows.

72 inch, 84 inch, 96 inch, and 102 inch wide for Bush Hog 3860 Loaders.

These buckets utilize a replaceable bolt-on cutting edge.

These buckets are equipped with a clevis mounting point for lifting. Refer to Figure 1.

CAUTION

NEVER LIFT ANY LOAD FROM ANY POINT OF THE LOADER WITH A CHAIN, ROPE, OR CABLE UNLESS LOADER IS EQUIPPED WITH A BUSH HOG FACTORY APPROVED ATTACHMENT WHICH WAS DESIGNED AND BUILT FOR THIS TYPE OF LIFTING. ALWAYS FOLLOW LIFTING INSTRUCTIONS INCLUDED WITH THIS ATTACHMENT.

NEVER TOW FROM ANY POINT OF THE LOADER WITH A CHAIN, ROPE, OR CABLE. DOING SO COULD CAUSE A ROLL OVER OR SERIOUS DAMAGE TO THE LOADER.

MAXIMUM LOAD LIMIT ON BUSH HOG CLEVIS AND CLEVIS MOUNTING POINT IS 6500 POUNDS. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE DAMAGE TO LOADER AND/OR INJURY TO OPERATOR.

Figure 1

(1)Bucket, heavy duty, high capacity.

(2)Clevis mounting point.

(3)Clevis (use only Factory approved clevis).

(4)Clevis pin.

(5)Cotter Pin.

SINGLE TINE KIT

Single tine kits are available for mounting on pre- punched buckets as follows. Each single tine kit includes one tine and attaching hardware.

72 inch quick draw buckets are punched for eight (8) single tine kits.

84 inch quick draw buckets are punched for ten (10) single tine kits.

96 inch quick draw buckets are punched for ten (10) single tine kits.

32

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Bush HOG Congratulations Table of Contents 3860 QTThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Tractor Important Safety PrecautionsLoader Safety Precautions Operating the LoaderEMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsIntroduction Introduction and DescriptionDescription Model 3860 QT Technical Specifications Tractor Preparation Installation InstructionsInstallation Important NoticeFront Bracket Forward SideSubframe Crosstube Lift and Support ALL Loader COMPO- Nents Safely Torque IdentificationInitial Loader Operation PRE-OPERATION InstructionsTransmission Fluid External Loader AND/OR Tractor ValveFloat Position Bucket Level IndicatorNeutral Position Initial Loader OperationRemote Hoses Support Daily Checks MaintenanceLoader Lubrication Bucket Level Gauge ROD General SafetyOperating Instructions OperationFilling the Bucket Lifting the LoadLowering the Bucket Carrying the LoadDumping the Bucket Not this Do this Dump Lower LeverFloat Operating with Float ControlFloat Surface Material Loading from a Bank 3RD CUT , 4TH CUT, ETC Do this Peeling and ScrapingBackfilling Loading LOW Trucks or Spreaders from a PileSoil Pile Back GradingTroubleshooting Procedures Problem Possible Cause Remedy Setting recommendedDismounting the Loader Page Mounting the Loader Page Installation & Operation of Quick Draw Latch Attach Upper channel Weld-in center support Bucket or attachment Installing Bucket or Attachment to Quick Draw Latch Attach Page Removing Bucket or Attachment from Quick Draw Latch Attach Quick Draw Bucket Bucket AttachmentSingle Tine KIT Super Penetrator Bale Probe Attachment Manure Fork Attachment Dozer AttachmentOperating Instructions for Dismounting Dozer from Loader Pallet Fork Attachment Parking AnglesGrapple Attachment Page Operating Instructions Page Supplemental Instructions For Ford Genesis Special Safety Decals Decals Torque Specifications American
Top Page Image Contents