Exmark Metro manual Blade Bolt Installation

Page 28

a)Disengage blades.

b)Stop engine and remove spark plug wire(s).

c)Raise deck, support properly using safety precautions.

d)Clean out any grass build-up from underside of deck and in deck discharge chute.

e)Inspect blades and sharpen or replace as required.

f)If blade removal is necessary, be careful for the sharp cutting edges of the blades.

g)Re-install the blades (if they were removed) and torque blade bolts to 75-80 ft/lbs. Be sure the spring disc washer cone is installed toward the bolt head (See Figure 14).

h)Remove jack stands (or equivalent support) and lower deck to ground.

FIG. 14

BLADE BOLT INSTALLATION

5.1.4Check safety interlock system.

Service Interval: Daily

a)For your safety, your Exmark mower is equipped with Operator Presence Controls, referred to as (OPC). When either the mower blades are engaged, or the transmission shifter lever is not in neutral and the operator removes both hands from the handles, the mower engine must stop.

b)To determine if the OPC is in operating condition, clear area of bystanders. Run the engine at one-third throttle, then with the drive levers and neutral lock latches in the “park brake” position, shift the transmission into gear and release the OPC levers – the engine MUST stop.

Again, run the engine at one-third throttle, move the transmission shifter lever to neutral, engage the blade clutch and release the OPC levers - the engine MUST stop.

If the mower engine does not stop under any of the above mentioned conditions, DO NOT OPERATE. Contact your authorized Exmark service dealer.

IMPORTANT: It is essential that all Operator Safety Mechanisms, be in place and in proper operating condition prior to mowing.

5.1.5Check Brake and Wheel Drive Linkage Adjustment.

Service Interval: Daily

Refer to Sections 3.8.5 and 3.8.6. Note any bent linkage or hardware which may need servicing or replacing.

-23 -

Image 28
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingPotential Hazard Operation Maintenance and Storage Safety Signs Riding AttachmentsPage Specifications Wheel Drive System DimensionsTires Assembly Instructions Torque RequirementsUpper Handle Height Adjustment Kohler Speed Control Throttle Cable HOOK-UPHP Kawasaki Speed Control Throttle Cable HOOK-UP 15 & 17 HP Kawasaki Speed Control Throttle Cable HOOK-UPFor 12.5 HP Kawasaki, 10.5 HP B&S and Kohler engines For 15 & 17 HP Kawasaki enginesLever and ROD Adjustment This Clearance should be Equal Shifter Lever To TransmissionNeutral Lock Lever Clearance Drive Lever Hardware LocationOperation Instructions ControlsDrive LEVER, Neutral LOCK/PARK Brake Latch Operation PRE-START Be sure ignition switch is in the OFF position Operating Instructions Rotating blades under the mower deck are dangerous Periodic Maintenance Maintenance and AdjustmentsTransporting Service Interval Daily Blade Bolt Installation Service Interval 40 hrs Service Interval 160 hrsLubrication Chart Service Interval Refer to ChartService Interval Spray Lubricant ChartPivot Points Adjustments Caster Height Adjustment Axle NO. of Spacers Number of 1/4 Blade Spacers PositionCutter Deck Belt Adjustment Blade Brake Adjustment 32 & 36 Belt Guide LocationDrive Belt Tension Adjustment Positions Trouble Shooting Blades do not Stop When DisengagedMower Pulling Left or Right Mower Cuts UnevenlyEngine Troubleshooting Engine Troubleshooting TableMower Deck Belt Routing 36 Mower DeckWiring Diagrams Warranty Page Service Record Date Description of Work DoneFold Along Appropriate Line Industrial Park BOX Exmark MFG. CO. INCBEATRICE, NE ALL Rights Reserved