Exmark LAZER Z HP manual Install Drive Wheels, Check Tire Pressure, Install Seat

Page 23

CAUTION

POTENTIAL HAZARD

♦If the ignition is in the “ON” position there is potential for sparks and engagement of components.

WHAT CAN HAPPEN

♦Sparks could cause an explosion or moving parts could accidentally engage causing personal injury.

HOW TO AVOID THE HAZARD

♦Be sure ignition switch is in the “OFF” position before charging the battery.

3.3.3Connect the negative battery cables.

NOTE: If the positive cable is also disconnected, connect the positive (red) cable and the red wire to the positive terminal on the battery first, then connect the negative (black) cable and white/white wire to the negative terminal on the battery (red wire and white/white wire are only on some units). Slip insulator boot over the positive terminal.

NOTE: If time does not permit charging the battery, or if charging equipment is not available, connect the negative battery cables and run the vehicle continuously for 20 to 30 minutes to sufficiently charge the battery.

3.4INSTALL DRIVE WHEELS.

3.4.1Mount drive wheels with the valve stem to the outside of the unit. Secure using four (4) 1/2-20 wheel nuts (installed on studs in hubs) for each wheel. Torque to 95 ft-lbs (128 NxM).

3.5CHECK TIRE PRESSURE.

3.5.1Check tire pressure in drive tires. Proper inflation pressure for tires is 13 psi (90 kPa). Adjust if necessary.

Semi-pneumatic caster tires do not need to be inflated.

3.6INSTALL SEAT

a)Remove seat assembly from the crate.

b)Remove the four 5/16-18 whizlock nuts from the seat track studs at the bottom of the seat. Retain for use later.

c)Align the seat track studs on the bottom of the seat with the holes in the seat frame. Place seat on top of the frame and secure with the four 5/16-18 whizlock nuts remove in step b).

3.7INSTALL CANISTER AIR CLEANER.

a)Remove air cleaner (with bracket attached) from crate. Keep air cleaner and mounting bracket together.

b)Remove the top two valve cover mounting screws from both left and right side engine valve covers. Keep screws for re-attaching air cleaner.

c)Position the air cleaner assembly over the engine, aligning air cleaner bracket holes with top holes in the valve covers. Reinstall valve cover screws through air cleaner bracket and torque to 70 in. lb. (4.9 N-m).

d)Remove plastic plugs from air intake elbow on engine and air cleaner hose. Adjust the air cleaner and hose as required and connect intake hose to air cleaner outlet. Position and tighten the two hose clamps to secure the hose connections.

-18 -

Page 22 Page 24
Image 23
Page 22 Page 24
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage For Kohler EFI Units Safety SignsPage Do not Operate Without Guard Page Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Torque Requirements DimensionsUncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Check Tire Pressure Install Drive WheelsInstall Seat Install Canister AIR CleanerControl ARM Shaft Install Motion Control LeversService Engine Service Hydraulic OIL Position Discharge ChuteMotion Control Positions Operation InstructionsControls Push the lever forward and down to disengage the brake Machine PRE-STARTOperating Instructions Transporting Maintenance & Adjustments Service Interval Monthly Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Kohler EFI engines only Service Interval 50 hoursService Interval 100 hrs Service Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval As Required Service Interval 80 hrsKohler EFI Fuel Line Routing Service Interval 500 hrs Service Interval After First 250 hrs Then yearly thereafterCutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentMule Drive Belt Adjustment Belt Guide Positioning Brake AdjustmentThrottle Tension No adjustment necessaryReverse Indicator Adjustment Motion Control Adjustment Motor OIL Disposal Caster AdjustmentWaste Disposal Mower Cuts Unevenly Trouble ShootingBattery Disposal Mower Pulls Left or Right W/LEVERS Fully ForwardEngine Warning Systems Engine Troubleshooting TableProblem Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents