Exmark LAZER Z HP manual Push the lever forward and down to disengage the brake

Page 26

CAUTION

POTENTIAL HAZARD

♦Machine can spin very rapidly by positioning one lever too much ahead of the other.

WHAT CAN HAPPEN

♦Operator may lose control of the machine, which may cause damage to the machine or injury.

HOW TO AVOID THE HAZARD

♦Use caution when making turns.

♦Slow the machine down before making sharp turns.

4.1.3Tracking Adjustment Knob : Located under the seat on the RH pump control link. Rotating this knob allows fine tuning adjustments so that the machine tracks straight with the drive levers in the full forward position.

Stop machine and wait for all moving parts to stop. Engage park brake. Unhook seat latch and tilt seat forward to gain access to the tracking knob. Rotate the knob clockwise (as viewed from the rear of the machine) to cause the machine to track more to the right and counterclockwise to cause the machine to track more to the left. Adjust in quarter-turn increments until the machine tracks straight. Check that the machine does not creep when in neutral with the park brakes disengaged.

IMPORTANT: Do not rotate the knob too far, as this may cause the machine to creep in neutral. Refer to section 5.2.13 for control linkage adjustment.

4.1.4PTO Engagement Switch: Located on right fuel tank.

Switch must be pulled out to the “ROTATE” position to engage the blades. Switch is pushed in to the “STOP” position to stop the blades.

4.1.5Choke Control: (All units except Kohler EFI) Located on right fuel tank.

Choke is used to aid in starting a cold engine. Moving the choke lever forward will put the choke in the “ON” position and moving the choke lever to the rear will put the choke in the “OFF” position. DO NOT run a warm engine with choke in the “ON” position.

4.1.6Throttle Control: Located on right fuel tank.

Throttle is used to control engine speed. Moving throttle lever forward will increase engine speed and moving throttle lever to the rear will decrease engine speed.

4.1.7Brake Lever: Located on left side of unit, just to the front of the console. The brake lever engages a parking brake on the drive wheels.

Pull the lever up and rearward to engage the brake.

Push the lever forward and down to disengage the brake.

The unit must be tied down and brake engaged when transporting.

4.1.8Ignition Switch: Located on right fuel tank.

The ignition switch is used to start and stop the engine. The switch has three positions “OFF”, “ON” and “START”. Insert key into switch and rotate clockwise to the “ON” position. Rotate clockwise to the next position to engage the starter (key must be held against spring pressure in this position).

Brake must be engaged, motion control levers out (neutral lock position) and PTO switch “OFF” to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

4.1.9Hour Meter: Located on the right fuel tank. The hour meter is connected to a pressure switch installed in the engine block and it records the number of hours that the engine has run. If the ignition switch is left on without engine running, hour meter will not run.

-21 -

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs For Kohler EFI UnitsPage Do not Operate Without Guard Page Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Install Canister AIR Cleaner Install Drive WheelsInstall Seat Check Tire PressurePosition Discharge Chute Install Motion Control LeversService Engine Service Hydraulic OIL Control ARM ShaftMotion Control Positions Operation InstructionsControls Push the lever forward and down to disengage the brake PRE-START MachineOperating Instructions Transporting Maintenance & Adjustments Service Interval Monthly Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Kohler EFI engines only Service Interval 50 hoursService Interval 100 hrs Service Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval 80 hrs Service Interval As RequiredKohler EFI Fuel Line Routing Service Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningThrottle Tension No adjustment necessaryReverse Indicator Adjustment Motion Control Adjustment Motor OIL Disposal Caster AdjustmentWaste Disposal Mower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Warning Systems Engine Troubleshooting TableProblem Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents