Exmark LAZER Z HP manual Service Interval 80 hrs, Service Interval As Required

Page 38

5.1.18Lubricate brake handle pivot:

Service Interval: 160 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Lubricate bronze bushings on brake handle pivot with a spray type lubricant or light oil.

5.1.19Lubricate brake rod bushings:

Service Interval: 160 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Unhook seat latch and tilt seat up.

c)Lubricate bronze bushings on each end of brake rod shaft with a spray type lubricant or a light oil (bushings are located to the inside of the flange bearings).

5.1.20Lubricate motion control bronze bushings:

Service Interval: 160 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Unhook seat latch and tilt seat up.

c)Lubricate bronze bushings on flange bearings securing the motion control arm shafts with a light oil or a spray type lubricant.

5.1.21Remove engine shrouds and clean cooling fins:

Service Interval: 80 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Remove cooling shroud clean-out covers from engine and clean cooling fins. Also clean dust, dirt, and oil from external surfaces of engine, which can cause improper cooling.

c)Make sure cooling shroud clean-out covers are reinstalled. Operating the engine without cooling shroud clean-out covers will cause engine damage due to overheating.

5.1.22Check spark plugs:

Service Interval: 160 hrs.

a)Remove spark plugs, check condition and reset gaps, or replace with new plugs. See Engine Owners Manual.

5.1.23Change fuel filter:

Service Interval: As Required

a)A fuel filter is installed between the fuel tanks and the engine. Replace when necessary.

For Kohler EFI Units:

WARNING

POTENTIAL HAZARD

♦Fuel system components are under high pressure.

WHAT CAN HAPPEN

♦The use of improper components can result in system failure, gasoline leakage and possible explosion.

HOW TO AVOID THE HAZARD

♦Use only approved fuel lines and fuel filters for high pressure systems.

- 33 -

Page 37 Page 39
Image 38
Page 37 Page 39
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs For Kohler EFI UnitsPage Do not Operate Without Guard Page Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Install Canister AIR Cleaner Install Drive WheelsInstall Seat Check Tire PressurePosition Discharge Chute Install Motion Control LeversService Engine Service Hydraulic OIL Control ARM ShaftMotion Control Positions Operation InstructionsControls Push the lever forward and down to disengage the brake PRE-START MachineOperating Instructions Transporting Maintenance & Adjustments Service Interval Monthly Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Kohler EFI engines only Service Interval 50 hoursService Interval 100 hrs Service Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval 80 hrs Service Interval As RequiredKohler EFI Fuel Line Routing Service Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningThrottle Tension No adjustment necessaryReverse Indicator Adjustment Motion Control Adjustment Motor OIL Disposal Caster AdjustmentWaste Disposal Mower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Warning Systems Engine Troubleshooting TableProblem Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents