Exmark LAZER Z HP manual Operation Instructions, Controls, Motion Control Positions

Page 25

NOTE: The baffle is labeled “HOT” and “COLD”. The oil level varies with the temperature of the oil. The “HOT” level shows the level of oil when it is at 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150° F (65°C). Fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75° F (24°C)), fill only to the “COLD” level.

4.OPERATION INSTRUCTIONS

4.1CONTROLS

4.1.1Familiarize yourself with all controls before operating the mower.

4.1.2Motion Control Levers: Located on each side of the console. The left lever controls the flow of hydraulic oil from the left hydrostatic pump to the left drive wheel motor. The right lever controls the flow of hydraulic oil from the right hydrostatic pump to the right drive wheel motor.

IMPORTANT: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will kill.

When levers are centered in the T-slot the drive system is in the neutral position. With levers moved out in the T-slot the drive system is in the neutral lock position (See Figure 6).

FIGURE 6

MOTION CONTROL POSITIONS

By moving both levers an equal amount forward or back from the neutral position the machine can be caused to move forward or backward in a straight line.

Movement of the left lever forward will cause the left drive wheel to rotate in a forward direction. Movement of the right lever forward will cause the right drive wheel to rotate in a forward direction. To stop forward travel, pull the levers back to the neutral position.

To turn left while moving forward, move the left lever back toward neutral to slow the left drive wheel.

To turn right while moving forward, move the right lever back toward neutral to slow the right drive wheel.

To make a zero turn to the left, pull the left lever back beyond neutral while holding the right lever slightly ahead of neutral.

To make a zero turn to the right, pull the right lever back beyond neutral while holding the left lever slightly ahead of neutral.

Pulling the levers back from the neutral position will cause the respective drive wheels to rotate in a reverse direction (spring tension can be felt when moving into reverse from neutral).

To turn to the left while backing, move the left lever forward toward neutral. To turn to the right while backing, move the right lever forward toward neutral.

- 20 -

Page 24 Page 26
Image 25
Page 24 Page 26
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage For Kohler EFI Units Safety SignsPage Do not Operate Without Guard Page Specifications Tires Hydrostatic Ground Drive SystemCutting Deck Torque Requirements DimensionsUncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Drive WheelsInstall Canister AIR Cleaner Check Tire PressureService Engine Service Hydraulic OIL Install Motion Control LeversPosition Discharge Chute Control ARM ShaftControls Operation InstructionsMotion Control Positions Push the lever forward and down to disengage the brake Machine PRE-STARTOperating Instructions Transporting Maintenance & Adjustments Service Interval Daily Periodic MaintenanceService Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 100 hrs Kohler EFI engines only Service Interval 50 hoursService Interval 40 hr Service Interval 40 hrs Lubrication ChartService Interval Refer to chart Caster Wheel Assembly Service Interval Once YearlyService Interval 160 hrs Service Interval As Required Service Interval 80 hrsKohler EFI Fuel Line Routing Service Interval 500 hrs Service Interval After First 250 hrs Then yearly thereafterCutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentMule Drive Belt Adjustment Belt Guide Positioning Brake AdjustmentReverse Indicator Adjustment No adjustment necessaryThrottle Tension Motion Control Adjustment Waste Disposal Caster AdjustmentMotor OIL Disposal Battery Disposal Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableEngine Warning Systems Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents