Exmark LAZER Z HP manual Check rollover protections systems roll bar pins

Page 34

Try to start with operator in seat, parking brake engaged, PTO engaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, PTO disengaged, and the left motion control lever in, starter must not crank, repeat again with the right lever in, then with both levers in - starter must not crank.

b)Check the kill circuits. Run engine at one-third throttle, disengage parking brake and raise off of seat (but do not get off of machine) engine must stop after approx. 1/2 second has elapsed (seat has time delay kill switch to prevent cut-outs on rough terrain).

Run engine at one-third throttle, engage PTO and raise off of seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Run engine at one-third throttle, with brake disengaged, move levers in and raise off seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Again, run engine at one-third throttle, brake engaged, and move left motion control lever in - engine must stop.

Repeat again moving the right lever in, then moving both levers in - engine must stop whether operator is on seat or not.

NOTE: If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK SERVICE DEALER.

IMPORTANT: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing.

5.1.7Check rollover protections systems (roll bar) pins

Service Interval: Daily

a)Make sure latch pin and hair pin are fully installed and lanyard is in good condition.

5.1.8Check for loose hardware.

Service Interval: Daily

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

5.1.9Service air cleaner.

Service Interval: 50 hrs.

More often under severe conditions.

See Engine manual for additional information.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Loosen retaining clips and remove air cleaner compartment cover.

c)Remove paper element. Check the condition of the paper element. Replace if dirty, bent or damaged.

d)Check the condition of the inner element. Replace whenever it appears dirty, typically every other time the paper element is replaced. Clean the base around the inner element before removing, so dirt does not get into the engine.

e)DO NOT wash or use pressurized air to clean paper element or inner element.

f)Reinstall elements. Position the cover so that the rubber dust ejector is pointing downward and secure with retaining clips.

- 29 -

Page 33 Page 35
Image 34
Page 33 Page 35
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs For Kohler EFI UnitsPage Do not Operate Without Guard Page Specifications Tires Hydrostatic Ground Drive SystemCutting Deck Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Canister AIR Cleaner Install Drive WheelsInstall Seat Check Tire PressurePosition Discharge Chute Install Motion Control LeversService Engine Service Hydraulic OIL Control ARM ShaftControls Operation InstructionsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START MachineOperating Instructions Transporting Maintenance & Adjustments Service Interval Daily Periodic MaintenanceService Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 100 hrs Kohler EFI engines only Service Interval 50 hoursService Interval 40 hr Service Interval 40 hrs Lubrication ChartService Interval Refer to chart Caster Wheel Assembly Service Interval Once YearlyService Interval 160 hrs Service Interval 80 hrs Service Interval As RequiredKohler EFI Fuel Line Routing Service Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningReverse Indicator Adjustment No adjustment necessaryThrottle Tension Motion Control Adjustment Waste Disposal Caster AdjustmentMotor OIL Disposal Mower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyProblem Engine Troubleshooting TableEngine Warning Systems Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents