Exmark LAZER Z HP manual Belt Guide Positioning, Brake Adjustment

Page 45

FIGURE 14

BELT GUIDE POSITIONING

5.2.8Brake Link Adjustment.

Check to make sure brake is adjusted properly.

a)Disengage brake lever (lever down).

b)Measure the length of the spring. Measurement should be 2.75” (7.0 cm) between washers (see Figure 15).

c)If adjustment is necessary, tighten the nut directly below the yoke and loosen the bottom nut (bottom one of the two tightened together) below the spring. Turn the nut directly below the washer (top nut of the two tightened together) until the correct measurement is obtained. Tighten the two nuts together and repeat on opposite side of unit. Turn clockwise to shorten spring length and turn counter-clockwise to lengthen the spring.

3/16” (4.8 mm) to 1/4” (6.4 mm)

2.75” (7.0 cm)

FIGURE 15

BRAKE ADJUSTMENT

5.2.9Brake Adjustment.

a)Check for brake link 2.75” (7.0 cm) measurement as described in section 5.2.8.

b)Engage brake lever (lever up).

c)Measure the distance between the trunion roller and the rod collar. Measurement should be 3/16” (4.8 mm) to 1/4” (6.4 mm). See Figure 15.

d)If adjustment is necessary, loosen the nut directly below the yoke. Turn the bottom nut (below washer) until the correct measurement is obtained (See Figure 14) turn nut clockwise to lengthen the gap (screws rod into yoke) and turn counter-clockwise to shorten the gap (screws rod out of yoke). Tighten nut against yoke and check opposite side of unit, repeat if necessary.

5.2.10Adjust Throttle Lever Tension.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Tension in throttle lever can be adjusted by adjusting the tightness of the lever pivot bolt, which is located under the console (See Figure 16).

-40 -

Page 44 Page 46
Image 45
Page 44 Page 46
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage For Kohler EFI Units Safety SignsPage Do not Operate Without Guard Page Specifications Hydrostatic Ground Drive System TiresCutting Deck Torque Requirements DimensionsUncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Seat Install Drive WheelsInstall Canister AIR Cleaner Check Tire PressureService Engine Service Hydraulic OIL Install Motion Control LeversPosition Discharge Chute Control ARM ShaftOperation Instructions ControlsMotion Control Positions Push the lever forward and down to disengage the brake Machine PRE-STARTOperating Instructions Transporting Maintenance & Adjustments Periodic Maintenance Service Interval DailyService Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Kohler EFI engines only Service Interval 50 hours Service Interval 100 hrsService Interval 40 hr Lubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval Once Yearly Caster Wheel AssemblyService Interval 160 hrs Service Interval As Required Service Interval 80 hrsKohler EFI Fuel Line Routing Service Interval 500 hrs Service Interval After First 250 hrs Then yearly thereafterCutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentMule Drive Belt Adjustment Belt Guide Positioning Brake AdjustmentNo adjustment necessary Reverse Indicator AdjustmentThrottle Tension Motion Control Adjustment Caster Adjustment Waste DisposalMotor OIL Disposal Battery Disposal Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemEngine Warning Systems Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents