Exmark LAZER Z HP manual Waste Disposal, Motor OIL Disposal, Caster Adjustment

Page 48

f)Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake.

g)The reverse indicator spring must be correct before the following adjustments can be made. See Section 5.2.12.

NOTE: The motion control lever needs to be in neutral while making any necessary adjustments.

The left rod assembly controls the left wheel and the right rod assembly controls the right wheel.

h)Bring the LH motion control lever into the neutral position. Adjust LH pump control rod length by rotating the double nuts on the rod in the appropriate direction until the wheels slightly creep in reverse. (See Figure 18) Move the motion control lever to the reverse position and while applying slight pressure to the lever allow the reverse indicator spring to bring the levers back to neutral. The wheel must stop turning or slightly creep in reverse. When adjustment is complete, tighten lock nuts onto ball joints.

i)Bring the RH motion control lever into the neutral position. Adjust the RH pump control rod length by rotating the tracking adjustment knob in the appropriate direction until the wheels slightly creep in reverse. Move the motion control lever to the reverse position and while applying slight pressure to the lever allow the reverse indicator spring to bring the levers back to neutral. The wheel must stop turning or slightly creep in reverse. See Figure 18.

j)Shut off unit. Remove jumper wire from wire harness connector and plug connector into seat switch.

5.2.14 Caster pivot bearings pre-load adjustment.

a)Remove dust cap from caster and tighten

nyloc nut until washers are flat and back off 1/4 of a turn to properly set the pre-load on the bearings. If disassembled, make sure the spring washers are reinstalled as shown in Figure 19.

5.2.15Seat armrest adjustment.

a)Lift armrest on seat. Locate square tab marked with the numbers 1 through 4. Rotate square tab 1/4 turn to raise or lower the armrest in approximately 1/4” (6.4 mm) increments. See Figure 20.

FIGURE 19

CASTER ADJUSTMENT

Armrest Adjustment

Tab Rotate ¼ Turn

 

FIGURE 20

6. WASTE DISPOSAL

ARMREST ADJUSTMENT

6.1 MOTOR OIL DISPOSAL

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

- 43 -

Page 47 Page 49
Image 48
Page 47 Page 49
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs For Kohler EFI UnitsPage Do not Operate Without Guard Page Specifications Hydrostatic Ground Drive System TiresCutting Deck Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Drive Wheels Install SeatInstall Canister AIR Cleaner Check Tire PressureInstall Motion Control Levers Service Engine Service Hydraulic OILPosition Discharge Chute Control ARM ShaftOperation Instructions ControlsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START MachineOperating Instructions Transporting Maintenance & Adjustments Periodic Maintenance Service Interval DailyService Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Kohler EFI engines only Service Interval 50 hours Service Interval 100 hrsService Interval 40 hr Lubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval Once Yearly Caster Wheel AssemblyService Interval 160 hrs Service Interval 80 hrs Service Interval As RequiredKohler EFI Fuel Line Routing Service Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningNo adjustment necessary Reverse Indicator AdjustmentThrottle Tension Motion Control Adjustment Caster Adjustment Waste DisposalMotor OIL Disposal Trouble Shooting Battery DisposalMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemEngine Warning Systems Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents