Exmark LAZER Z HP Lubrication Chart, Service Interval 40 hrs, Service Interval Refer to chart

Page 36

5.1.13Check tire pressures:

Service Interval: 40 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Check tire pressure in drive tires.

c)Inflate drive tires to 13 psi (90 kPa).

d)Caster tires do not need to be inflated.

NOTE: Do not add any type of tire liner or foam fill material to the tires.

Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

5.1.14Check condition of belts:

Service Interval: 40 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Unhook seat latch and tilt seat up. Lift the rubber flap on front side of the engine to check pump drive belt.

c)Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

d)Check under machine to inspect the mule drive belt.

e)See Sections 5.2.3, through 5.2.5 for belt adjustment.

5.1.15Lubricate grease fittings:

Service Interval: Refer to chart.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

LUBRICATION CHART

 

FITTING

INITIAL

NO. of

SERVICE

 

LOCATIONS

PUMPS

PLACES

INTERVAL

1.

Front Caster wheel hubs

∗0

2

∗Yearly

2.

Front Caster Pivots

∗0

2

∗Yearly

3.

Height Adj. Shaft Bearings

1

5

40 hours

4.

Deck Drive Belt Idler Arm

1

1

Yearly

5.

Brake Brackets

1

2

200 hours

6.

Mule Drive Belt Idler Arm

1

1

Yearly

7.

Pump Drive Belt Idler Arm

1

1

Yearly

8.

Deck Rear Struts

1

2

40 hours

∗See Section 5.1.15 c) for special lubrication instructions on the front caster pivots and Section 5.1.16 for special lubrication instructions on the front casters wheel hubs.

No. 6 (Mule Drive Belt Idler Arm)

Located Under Engine Frame

No. 7 (Pump Drive Belt Idler Arm)

Located Under Engine Frame

- 31 -

Page 35 Page 37
Image 36
Page 35 Page 37
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs For Kohler EFI UnitsPage Do not Operate Without Guard Page Specifications Hydrostatic Ground Drive System TiresCutting Deck Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Drive Wheels Install SeatInstall Canister AIR Cleaner Check Tire PressureInstall Motion Control Levers Service Engine Service Hydraulic OILPosition Discharge Chute Control ARM ShaftOperation Instructions ControlsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START MachineOperating Instructions Transporting Maintenance & Adjustments Periodic Maintenance Service Interval DailyService Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Kohler EFI engines only Service Interval 50 hours Service Interval 100 hrsService Interval 40 hr Lubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval Once Yearly Caster Wheel AssemblyService Interval 160 hrs Service Interval 80 hrs Service Interval As RequiredKohler EFI Fuel Line Routing Service Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningNo adjustment necessary Reverse Indicator AdjustmentThrottle Tension Motion Control Adjustment Caster Adjustment Waste DisposalMotor OIL Disposal Trouble Shooting Battery DisposalMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemEngine Warning Systems Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents