Exmark LAZER Z HP Kohler EFI engines only Service Interval 50 hours, Service Interval 100 hrs

Page 35

5.1.10Check Spark Arrester

Kohler EFI engines only: Service Interval: 50 hours

WARNING

POTENTIAL HAZARD

♦Hot exhaust system components may ignite gasoline vapors even after the engine is stopped.

♦Hot particles exhausted during engine operation may ignite flammable materials.

WHAT CAN HAPPEN

♦Fire may result in personal injury or property damage.

HOW TO AVOID THE HAZARD

♦Do NOT refuel or run engine unless spark arrester is installed.

a)Shut off engine, remove key, and wait for all moving parts to stop.

b)Wait for muffler to cool.

c)If any breaks in the screen or welds are observed, replace arrester.

d)If plugging of the screen is observed, remove arrester and shake loose particles out of the arrester and clean screen with a wire brush (soak in solvent if necessary). Re-install arrester on exhaust outlet.

5.1.11Change engine oil:

Service Interval: 100 hrs.

NOTE: Change oil and filter after first five (5) hrs. of operation.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Drain oil while engine is warm from operation.

c)The oil drain valve is located on right hand side of engine.

Place pan under machine to catch oil and open valve with a 10 mm wrench. Allow oil to drain, then close valve.

d)Replace the oil filter every other oil change. Clean around oil filter and unscrew filter to remove. Before reinstalling new filter, apply a thin coating of oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter then tighten filter an additional 2/3 to 3/4 turn.

e)Clean around oil fill cap and remove cap. Fill to specified capacity and replace cap. Use oil recommended in engine owner’s manual. DO NOT overfill.

f)Start the engine and check for leaks.

5.1.12Check hydraulic oil level:

Service Interval: 40 hr.

a)Stop engine and wait for all moving parts to stop.

b)Unhook seat latch and tilt seat up.

c)Clean area around hydraulic reservoir cap and remove cap. Oil level should be to the top of the baffle inside the tank. If not, add oil. Use only Mobil 1 15W-50 synthetic motor oil. Replace hydraulic reservoir cap and tighten until snug. Do not overtighten.

NOTE: The baffle is labeled “HOT” and “COLD”. The oil level varies with the temperature of the oil. The “HOT” level shows the level of oil when it is at 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150° F (65°C), fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75° F (24°C)), fill only to the “COLD” level.

-30 -

Page 34 Page 36
Image 35
Page 34 Page 36
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage For Kohler EFI Units Safety SignsPage Do not Operate Without Guard Page Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Torque Requirements DimensionsUncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Check Tire Pressure Install Drive WheelsInstall Seat Install Canister AIR CleanerControl ARM Shaft Install Motion Control LeversService Engine Service Hydraulic OIL Position Discharge ChuteMotion Control Positions Operation InstructionsControls Push the lever forward and down to disengage the brake Machine PRE-STARTOperating Instructions Transporting Maintenance & Adjustments Service Interval Monthly Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Kohler EFI engines only Service Interval 50 hoursService Interval 100 hrs Service Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval As Required Service Interval 80 hrsKohler EFI Fuel Line Routing Service Interval 500 hrs Service Interval After First 250 hrs Then yearly thereafterCutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentMule Drive Belt Adjustment Belt Guide Positioning Brake AdjustmentThrottle Tension No adjustment necessaryReverse Indicator Adjustment Motion Control Adjustment Motor OIL Disposal Caster AdjustmentWaste Disposal Mower Cuts Unevenly Trouble ShootingBattery Disposal Mower Pulls Left or Right W/LEVERS Fully ForwardEngine Warning Systems Engine Troubleshooting TableProblem Electrical Diagram Kohler 23 & 27 HP AIR-COOLED Units Electrical Diagram Kohler EFI Units Hydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories
Related manuals
Manual 24 pages 40.18 Kb

LAZER Z HP specifications

The Exmark LAZER Z HP is a standout zero-turn lawn mower known for its exceptional performance, durability, and user-friendly design. Ideal for both residential and commercial landscapers, this machine combines cutting-edge technology with practical features to deliver a top-notch mowing experience.

One of the main features of the LAZER Z HP is its powerful engine options. Available with either Kohler or Kawasaki engines, this mower provides reliability and robust performance. With horsepower ranging from 22 to 27, it can tackle even the toughest mowing conditions, whether it's thick grass or uneven terrain. This power is matched by an efficient fuel system that ensures long operational periods without frequent refueling.

Another notable aspect of the LAZER Z HP is its innovative cutting technology. Equipped with a patented UltraCut deck, the mower is designed for superior grass handling and an exceptional cut quality. The deck is available in various sizes, typically ranging from 48 to 60 inches, allowing users to choose the most suitable option for their lawn size and type. The unique design of the mower deck promotes an even cut and excellent discharge, ensuring that clippings are finely shredded and evenly spread across the lawn.

The LAZER Z HP also boasts a user-friendly interface. Its intuitive controls and ergonomic seating allow for comfortable operation over extended periods. The adjustable seat and control arms can be customized to fit the operator, reducing fatigue and enhancing productivity. Additionally, the dual hydrostatic drive system enables smooth and precise maneuverability, allowing users to navigate around obstacles with ease.

Durability is a hallmark of the Exmark brand, and the LAZER Z HP is no exception. Constructed with high-quality materials, it features a robust frame and durable components designed to withstand the rigors of daily use. Exmark's commitment to quality ensures that owners can rely on this mower season after season.

Overall, the Exmark LAZER Z HP is an impressive machine that merges power, precision, and user comfort. With its innovative cutting technology, robust engine options, and durable design, it stands out as a top choice for anyone looking to maintain a pristine lawn. Whether you are a professional landscaper or a dedicated homeowner, the LAZER Z HP delivers the performance and reliability needed to achieve outstanding results.
Top Page Image Contents