Ferris Industries 5901178, 5901180, 5901181, 5901179 Mowing Recommendations, Height of Grass

Page 26

Operation

Operation

MOWING

1.Engage the parking brake. Make sure the PTO switch is disengaged, the motion control handles are locked in the NEUTRAL position and the operator is on the seat.

2.Start the engine (see STARTING THE ENGINE).

3.Set the mower cutting height.

4.Set the throttle to FULL.

5.Engage the PTO by pulling up on the PTO switch.

6.Begin mowing.

7.When finished, slow engine down and shut off the PTO.

8.Stop the engine (see STOPPING THE TRACTOR AND ENGINE).

MOWING RECOMMENDATIONS

Several factors can affect how well your machine cuts grass, Following proper mowing recommendations can improve the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference. Typically, you should mow the grass when it is is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass, the amount of rainfall, the prevailing temperature, and the lawn’s overall condition.

Cutting the grass too short causes weak, thin grass plants, which are easily damaged by dry periods and pests. Cutting too short is often more damaging than allowing the grass to be slightly higher.

Letting grass grow a bit longer—especially when it is hot and dry—reduces heat build-up, preserves needed moisture and protects the grass from heat damage and other problems. However, allowing grass to grow too high can cause thin turf and additional problems.

Cutting off too much at one time shocks the plant’s growth system and weakens the grass plants. A good rule of thumb is the 1/3 rule: to cut no more than one third of the grass height, and never more than 1 inch at a time.

The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using (for example, broadcasting with side discharge decks can process a much larger volume of grass than mulching does).

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum for the first pass, and then reset it to the desired height and mow a second or third time.

Don’t cover the grass surface with a heavy layer of clippings. Consider using a grass collection system and starting a compost pile.

Cut Here On

 

 

Cut

First Pass

 

 

Here On

 

 

 

 

Second

 

 

 

 

Pass

 

 

 

24

www.ferrisindustries.com

Image 26
Contents Ferris Industries 5100798 DescriptionModel Number Date Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Children Slope OperationTowed Equipment RIDE-ON Units EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt All Models Identification NumbersCE Identification TAG Markings CE ModelsSafety Decals Safety DecalsSafety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversVoltage Indicator PTO Power Take Off SwitchGlow Plug Indicator diesel model only Hour Meter / Maintenance ReminderChecks Before Starting General Operating SafetyOperation Diesel Model Only Priming the Fuel SystemTo prime the fuel system On the water separatorGas Model Starting the EngineStopping the Tractor & Engine Diesel ModelDriving the Tractor Pushing the Rider by HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place To lower the roll bar Attaching a TrailerRaise & Lower the Roll BAR To raise the roll barHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingProper Mulching Temporary Storage 30 Days Or Less Starting After Long Term StorageDiesel Fuel Recommendations Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Rider Maintenance Regular MaintenanceSafety Items Engine MaintenanceFuel Filter To add fuelChecking / Adding Fuel Gas Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberPressurized System Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustment & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Position Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Return Spring AdjustmentParking Brake Adjustment Mowing Height AdjustmentDeck Lift ROD Timing Adjustment Deck Height Pin Position4 Locations Deck Leveling AdjustmentDeck Lift Spring Less Pre-Load Suspension AdjustmentTo adjust the spring pre-load More Pre-LoadPTO Clutch Adjustment Blade Brake CheckPump Drive Belt Removal Belt Removal & ReplacementPump Drive Belt Replacement PTO Drive Belt Removal PTO Drive Belt ReplacementSpindle Drive Belt Removal Replacement PTO Belt Routing Jump Starting with Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Engine SpecificationsDimensions ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.