Ferris Industries 5901179, 5901180, 5901181, 5901178, 5900626, 5900621 manual Fuel Filter, To add fuel

Page 33

CHECKING / ADDING FUEL (Diesel)

To add fuel:

1.Remove the fuel cap (A, Figure 13).

2.Fill the tank to the bottom of the fill tube. This will leave room in the tank for fuel expansion. Refer to your engine manual for specific fuel recommendations.

3.Install and hand tighten the fuel cap.

4.Repeat same process for opposite tank.

NOTE: The fuel tanks are tied together through a “tee” in the supply lines. By filling only one tank, the level will balance between the two tanks, effectively having 1/2 tank of fuel for each side. The fuel transfer through the “tee” is slow, so it is recommended that both tanks have fuel added to them.

FUEL FILTER

This unit is equipped with two fuel filters. One is a water separator/filter mounted to the frame, under the seat and the other is located on the engine. The water separator should be drained every 25 hours or whenever water is visible in the bowl. Replace the fuel filters every 500 hours of operation or as required.

To drain the fuel filter:

1.Turn the engine off, set the parking brake, remove the ignition key, and wait for all moving parts to stop.

2.Allow the engine to cool for five (5) minutes before draining the fuel filter.

3.Place a container under the drain valve (A, Figure 14) and turn the drain valve approximately 1-2 turns.

4.Allow the filter to drain until all water and debris have drained out.

5.Turn the drain valve to close it when finished draining.

WARNING

Diesel fuel is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

Do not drain or replace fuel filter when engine is hot, as spilled fuel may ignite. Make sure the filter drain valve is fully closed before returning the unit to service.

Operation

A

Figure 13. Fuel Tank Fill

A. Fuel Tank Cap

A

Figure 14. Drain Fuel Filter

A. Drain Valve

Do not use Kerosene in place of diesel fuel. Kerosene will damage the engine.

Consult the engine manufacturer’s manual for specific fuel recommendations.

WARNING

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the ignition switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.

The water separator is under suction during normal engine operation. Ensure the drain valve is tightened securely to help prevent air from entering the fuel system.

Operation

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Description Model NumberFerris Industries 5100798 Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsService and Maintenance Maintenance and StorageSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings Identification NumbersAll Models CE ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Seat Adjustment Lever Features & ControlsIgnition Switch Ground Speed LeversGlow Plug Indicator diesel model only PTO Power Take Off SwitchVoltage Indicator Hour Meter / Maintenance ReminderGeneral Operating Safety OperationChecks Before Starting To prime the fuel system Priming the Fuel SystemDiesel Model Only On the water separatorStopping the Tractor & Engine Starting the EngineGas Model Diesel ModelPushing the Rider by Hand Driving the TractorSmooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Raise & Lower the Roll BAR Attaching a TrailerTo lower the roll bar To raise the roll barMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Diesel Fuel Recommendations Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Safety Items Regular MaintenanceRider Maintenance Engine MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Check / Change AIR Filter Check Hydraulic OIL Level Check / ADD Engine OILHydraulic OIL Filter Change Change Interval Every 500 Hours Filter Part NumberChange Engine Coolant Clean RADIATOR, Screen & OIL Cooler Check Engine Coolant LevelPressurized System Lubrication GreaseOil Battery Maintenance Cleaning the Battery and CablesANTI-SCALP Deck Casters Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Neutral Adjustment Neutral Position and Return Spring AdjustmentNeutral Position Adjustment Return Spring AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing AdjustmentDeck Leveling Adjustment Deck Lift Spring4 Locations To adjust the spring pre-load Suspension AdjustmentLess Pre-Load More Pre-LoadBlade Brake Check PTO Clutch AdjustmentBelt Removal & Replacement Pump Drive Belt ReplacementPump Drive Belt Removal PTO Drive Belt Replacement Spindle Drive Belt Removal ReplacementPTO Drive Belt Removal PTO Belt Routing Battery Service Checking Battery VoltageJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Dimensions SpecificationsEngine ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents