Ferris Industries 5900621 manual Troubleshooting, Adjustment & Service, Troubleshooting the Mower

Page 41

Troubleshooting, Adjustment & Service

Rider Troubleshooting Continued.

PROBLEM

CAUSE

REMEDY

Engine runs, but rider will

1.

Hydraulic dump valve(s)

1. Turn dump valve(s) clockwise to close.

not drive.

 

in “open” position.

 

Torque to 80-120 in.lbs. (9-13.5 N.m.)

 

2.

Belt is broken.

2.

See Drive Belt Replacement.

 

3.

Drive belt slips.

3.

See problem and cause below.

 

4.

Brake is not fully released.

4.

See authorized service dealer

 

 

 

 

 

Hydraulic pump drive belt slips.

1.

Pulleys or belt greasy or oily.

1.

Clean as required.

 

2.

Belt stretched or worn.

2.

Replace belt.

 

 

 

 

 

Brake will not hold.

1.

Brake is incorrectly adjusted.

1.

See Brake Adjustment.

 

2.

Brake caliper pads worn.

2.

Replace with new brake pads.

 

 

 

 

 

Rider steers or handles poorly.

1.

Steering linkage is loose.

1.

Check and tighten any loose connections.

 

2.

Improper tire inflation.

2.

See Regular Maintenance Section.

 

 

 

 

 

TROUBLESHOOTING THE MOWER

PROBLEM

CAUSE

REMEDY

Mower will not raise.

1.

Lift linkage not properly attached

1.

See authorized service dealer for repair.

 

 

or damaged.

 

 

 

 

 

 

 

Engine stalls easily with

1.

Engine speed too slow.

1.

Set to full throttle.

mower engaged.

2.

Ground speed too fast.

2. Decrease Ground Speed.

 

3.

Cutting height set too low.

3.

Cut tall grass at maximum cutting

 

 

 

 

height during first pass.

 

4.

Discharge chute jamming

4.

Cut grass with discharge pointing toward

 

 

with cut grass.

 

previously cut area.

 

 

 

 

Excessive mower vibration.

1.

Blade mounting bolts

1. Tighten to 70 ft.lbs. (94 N.m.).

 

 

are loose.

 

 

 

2.

Mower blades, spindles,

2.

Check and replace as necessary.

 

 

or pulleys are bent.

 

 

 

3.

Mower blades are out

3. Remove, sharpen, and balance blades.

 

 

of balance.

 

See Maintenance Section.

 

4.

Belt installed incorrectly.

4.

Reinstall Correctly.

 

 

 

 

 

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

1.

Repair or replace.

 

2.

Using incorrect belt.

2.

Replace with correct belt.

Mower drive belt slips or fails to drive.

1.

Idler pulley spring broken or not

1.

Repair or replace as needed.

 

properly attached.

 

 

2.

Mower drive belt broken.

2.

Replace drive belt.

Troubleshooting

39

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Ferris Industries 5100798 DescriptionModel Number Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings Identification NumbersAll Models CE ModelsSafety Decals Safety DecalsSafety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Seat Adjustment Lever Features & ControlsIgnition Switch Ground Speed LeversGlow Plug Indicator diesel model only PTO Power Take Off SwitchVoltage Indicator Hour Meter / Maintenance ReminderChecks Before Starting General Operating SafetyOperation To prime the fuel system Priming the Fuel SystemDiesel Model Only On the water separatorStopping the Tractor & Engine Starting the EngineGas Model Diesel ModelPushing the Rider by Hand Driving the TractorSmooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Raise & Lower the Roll BAR Attaching a TrailerTo lower the roll bar To raise the roll barMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Diesel Fuel Recommendations Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Safety Items Regular MaintenanceRider Maintenance Engine MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Check / Change AIR Filter Check Hydraulic OIL Level Check / ADD Engine OILHydraulic OIL Filter Change Change Interval Every 500 Hours Filter Part NumberPressurized System Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Adjustment Neutral Position and Return Spring AdjustmentNeutral Position Adjustment Return Spring AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing Adjustment4 Locations Deck Leveling AdjustmentDeck Lift Spring To adjust the spring pre-load Suspension AdjustmentLess Pre-Load More Pre-LoadBlade Brake Check PTO Clutch AdjustmentPump Drive Belt Removal Belt Removal & ReplacementPump Drive Belt Replacement PTO Drive Belt Removal PTO Drive Belt ReplacementSpindle Drive Belt Removal Replacement PTO Belt Routing Jump Starting with Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Dimensions SpecificationsEngine ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents