Ferris Industries 5900621, 5901180, 5901181 Check / ADD Engine OIL, Hydraulic OIL Filter Change

Page 35

Regular Maintenance

CHECK / ADD ENGINE OIL

 

Refer to Figure 15 for dipstick and oil fill locations.

 

Refer to the engine owners manual for specific engine

A

oil check and fill procedures. Also refer to the engine

 

owners manual for specific engine oil and filter

B

change procedures.

Diesel Model

A

B

CHECK / CHANGE AIR FILTER

Refer to the engine owners manual for specific air filter service procedures.

CHECK HYDRAULIC OIL LEVEL

NOTE: Do not open the hydraulic oil reservoir unless oil is being added.

1.Visually check that the hydraulic oil level is filled to the recess area (A, Figure 16) of the hydraulic oil reservoir.

2.If necessary, remove the reservoir cap (B) and add either Mobil 1™, 15W-50 synthetic oil or Castrol Syntec™ 5W-50 oil. DO NOT use conventional oils. Make sure area around the filler neck is free of dust, dirt, or other debris.

HYDRAULIC OIL FILTER CHANGE

Change Interval: Every 500 Hours

Filter Part Number: 5021357

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. Ferris recommends this be a dealer-only service item.

1.Locate the hydraulic oil filter (A, Figure 17) behind the oil reservoir.

2.Fill the new filter with oil. Lubricate the new filter seal with a few drops of oil.

3.Remove the oil filter and quickly thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

4.Refill reservoir with fresh oil to replace any oil lost during filter change.

5.Raise the rear of the unit and secure with jackstands. Chock the front wheels to prevent the unit from rolling. Run the unit for several minutes to purge any air from the hydraulic system and check the hydraulic oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

Gas Model

Figure 15. Change Oil & Filter

A.Oil Fill Cap

B.Crankcase Dip Stick

 

A

B

 

Figure 16. Hydraulic Oil Reservoir

Maintenance

 

A.Tank Recess (“FULL” level)

B.Cap

A

Figure 17. Hydraulic Oil Filter Location

A. Oil Filter

33

Image 35
Contents Ferris Industries 5100798 DescriptionModel Number Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Models Identification NumbersCE Identification TAG Markings All ModelsSafety Decals Safety DecalsSafety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Ground Speed Levers Features & ControlsSeat Adjustment Lever Ignition SwitchHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator diesel model only Voltage IndicatorChecks Before Starting General Operating SafetyOperation On the water separator Priming the Fuel SystemTo prime the fuel system Diesel Model OnlyDiesel Model Starting the EngineStopping the Tractor & Engine Gas ModelPushing the Rider by Hand Driving the TractorReverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place To raise the roll bar Attaching a TrailerRaise & Lower the Roll BAR To lower the roll barTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Long Term Storage Longer Than 30 Days Starting After Long Term StorageDiesel Fuel Recommendations Temporary Storage 30 Days Or LessStorage Gas Model Operation Engine Maintenance Regular MaintenanceSafety Items Rider MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Change Interval Every 500 Hours Filter Part Number Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Hydraulic OIL Filter ChangePressurized System Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Return Spring Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Neutral Position AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing Adjustment4 Locations Deck Leveling AdjustmentDeck Lift Spring More Pre-Load Suspension AdjustmentTo adjust the spring pre-load Less Pre-LoadBlade Brake Check PTO Clutch AdjustmentPump Drive Belt Removal Belt Removal & ReplacementPump Drive Belt Replacement PTO Drive Belt Removal PTO Drive Belt ReplacementSpindle Drive Belt Removal Replacement PTO Belt Routing Jump Starting with Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Chassis SpecificationsDimensions EngineFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.