Ferris Industries 5901178, 5901180, 5901181 Belt Removal & Replacement, Pump Drive Belt Removal

Page 50

Troubleshooting, Adjustment & Service

Troubleshooting

BELT REMOVAL & REPLACEMENT

WARNING

If servicing the belts after the engine has been running, use extreme caution when raising the hood or lowering the rear shield. The surface of the hood and rear shield can be hot from the muffler and exhaust manifold.

Pump Drive Belt Removal

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt from the clutch (see PTO DRIVE BELT REMOVAL for instructions).

3.Using a 1/2” breaker bar, place the square end in the square hole located in the middle of the idler arm (A, Figures 49). Carefully rotate the breaker

bar COUNTER-CLOCKWISE, which will relieve the tension on the belts exerted from the idler arm.

4.Remove the belts from the right-hand and left- hand pump drive pulley grooves.

5.Carefully release the tension on the breaker bar.

6.Unhook the spring (B) from the anchor bolt on the idler arm.

7.Remove the belts from the crankshaft pulley grooves and pull out from behind the clutch.

Pump Drive Belt Replacement

1.Place the belts under clutch into the crankshaft pulley grooves.

2.Wrap the belts around the top side of the idler arm pulley and install the belts in the right-hand pump pulley grooves.

3.Reinstall the spring onto the anchor bolt on the idler arm.

4.Carefully rotate the idler arm with the breaker bar counter-clockwise (see Figure 49). While holding the breaker bar firmly, install the belts in the left- hand pump pulley grooves and the two stationary idler pulleys grooves.

5.Carefully release the tension on the breaker bar.

6.Inspect the belt path making sure that all belts are properly seated in the pulley grooves.

7.Reinstall the PTO drive belt from the clutch (see PTO DRIVE BELT REPLACEMENT for instructions).

B

A

Figure 49. Pump Belt Removal & Replacement

A.Pump Drive Idler Arm

B.Spring

To avoid damaging belts, DO NOT

PRY BELTS OVER PULLEYS.

WARNING

Use extreme caution when rotating the idler arm with the breaker bar, due to the increased tension in the spring as the idler arm is being rotated. Injury may result if the breaker bar is prematurely released while the spring is under tension.

48

www.ferrisindustries.com

Image 50
Contents Ferris Industries 5100798 DescriptionModel Number Date Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Children Slope OperationTowed Equipment RIDE-ON Units EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt All Models Identification NumbersCE Identification TAG Markings CE ModelsSafety Decals Safety DecalsSafety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversVoltage Indicator PTO Power Take Off SwitchGlow Plug Indicator diesel model only Hour Meter / Maintenance ReminderChecks Before Starting General Operating SafetyOperation Diesel Model Only Priming the Fuel SystemTo prime the fuel system On the water separatorGas Model Starting the EngineStopping the Tractor & Engine Diesel ModelDriving the Tractor Pushing the Rider by HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place To lower the roll bar Attaching a TrailerRaise & Lower the Roll BAR To raise the roll barHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingProper Mulching Temporary Storage 30 Days Or Less Starting After Long Term StorageDiesel Fuel Recommendations Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Rider Maintenance Regular MaintenanceSafety Items Engine MaintenanceFuel Filter To add fuelChecking / Adding Fuel Gas Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberPressurized System Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustment & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Position Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Return Spring AdjustmentParking Brake Adjustment Mowing Height AdjustmentDeck Lift ROD Timing Adjustment Deck Height Pin Position4 Locations Deck Leveling AdjustmentDeck Lift Spring Less Pre-Load Suspension AdjustmentTo adjust the spring pre-load More Pre-LoadPTO Clutch Adjustment Blade Brake CheckPump Drive Belt Removal Belt Removal & ReplacementPump Drive Belt Replacement PTO Drive Belt Removal PTO Drive Belt ReplacementSpindle Drive Belt Removal Replacement PTO Belt Routing Jump Starting with Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Engine SpecificationsDimensions ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.