Ferris Industries 5900626, 5901180 manual Deck Lift ROD Timing Adjustment, Deck Height Pin Position

Page 46

Troubleshooting, Adjustment & Service

Troubleshooting

DECK LIFT ROD TIMING

ADJUSTMENT

1.Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 18 psi (1,24 bar); front tires to 25 psi (1,72 bar).

2.Install the cutting height adjustment pin in the 3- 3/4” (9,5 cm) position. See Figure 38.

3.To check the lift rod timing, measure and record the distance between the lift pivots and the rod pivots. Repeat for other side of unit. See Figure 39.

4.If the measurements for the rods and pivots are equal,, no further adjustment is required. If the measurements are NOT equal (greater than 1/8” (3,17mm) difference), adjustment is required, continue with Step 5.

5.Refer to Figure 39. To adjust the lift rods, adjust the 5/8” hex nuts on either side of the front lift pivot until the measurements are equal. Repeat for other side. Make sure the nylon lock nut on the end of the rod towards the rear of the machine is loose to allow the rod to turn in the rear lift pivot.

6.Refer to Figure 40. Measure the distance from the front lift pivot to the ground and from the front chain anchor bolt to the ground. If the measurements are equal, no further adjustment is required. If the measurements are NOT equal (greater than 1/8” (3,17mm) difference), adjustment is required, continue with Step 7.

7.Raise the seat plate to access the center lift link (A, Figure 41).

8.Loosen the jam nut (C) on the lift clevis (D) and turn the adjuster bolt (B) until the measurements are equal. Tighten the jam nut against the lift clevis.

Figure 38. Deck Height Pin Position

Figure 39. Measure & Adjust Lift Rod Timing

Figure 40. Measure Front Lift Pivot

A

B

C

D

Figure 41. Center Lift Link Adjustment

A.Center Lift Link

B.Adjuster Bolt

C.Jam Nut

D.Lift Clevis

44

www.ferrisindustries.com

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Model Number DescriptionFerris Industries 5100798 Date Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Children Slope OperationTowed Equipment RIDE-ON Units EmissionsMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt All Models Identification NumbersCE Identification TAG Markings CE ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversVoltage Indicator PTO Power Take Off SwitchGlow Plug Indicator diesel model only Hour Meter / Maintenance ReminderOperation General Operating SafetyChecks Before Starting Diesel Model Only Priming the Fuel SystemTo prime the fuel system On the water separatorGas Model Starting the EngineStopping the Tractor & Engine Diesel ModelDriving the Tractor Pushing the Rider by HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn To lower the roll bar Attaching a TrailerRaise & Lower the Roll BAR To raise the roll barHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingProper Mulching Temporary Storage 30 Days Or Less Starting After Long Term StorageDiesel Fuel Recommendations Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Rider Maintenance Regular MaintenanceSafety Items Engine MaintenanceFuel Filter To add fuelChecking / Adding Fuel Gas Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberCheck Engine Coolant Level Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerPressurized System Grease LubricationOil Cleaning the Battery and Cables Battery MaintenanceANTI-SCALP Deck Casters Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustment & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Neutral Position Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Return Spring AdjustmentParking Brake Adjustment Mowing Height AdjustmentDeck Lift ROD Timing Adjustment Deck Height Pin PositionDeck Lift Spring Deck Leveling Adjustment4 Locations Less Pre-Load Suspension AdjustmentTo adjust the spring pre-load More Pre-LoadPTO Clutch Adjustment Blade Brake CheckPump Drive Belt Replacement Belt Removal & ReplacementPump Drive Belt Removal Spindle Drive Belt Removal Replacement PTO Drive Belt ReplacementPTO Drive Belt Removal PTO Belt Routing Checking Battery Voltage Battery ServiceJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Engine SpecificationsDimensions ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents