Ferris Industries 5901179, 5901180, 5901181, 5901178 Servicing the Mower Blades, Removing the Blade

Page 39

SERVICING THE MOWER BLADES

1.Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps.

2.To remove blade for sharpening, use a 1” wrench on the flats of the spindle shaft while removing the blade mounting bolt with a 15/16” wrench (Figure 28).

3.Use a file to sharpen blade to fine edge. Remove all nicks and dents in blade edge. If blade is severely damaged, it should be replaced.

4.Balance the blade as shown in Figure 29. Center the blade’s hole on a nail lubricated with a drop of oil. A balanced blade will remain level.

5.Reinstall each blade with the tabs pointing up toward deck as shown in Figure 30. Secure with a bolt and flat washer and torque bolts to 70 ft.lbs. (94 N.m.).

WARNING

Mower blades are sharp. For your personal safety, do not handle mower blades with bare hands. Careless or improper handling of blades may result in serious injury.For your personal safety, blade mounting bolts must each be installed with a flat washer then securely tightened. Torque blade mounting bolts to 70 ft.lbs. (94 N.m.)

Regular Maintenance

Figure 28. Removing the Blade

Nail

Figure 29. Balancing The Blade

A

Figure 30. Installing The Blade

A.Blade Bolt

B.Flat Washer

Maintenance

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Description Model NumberFerris Industries 5100798 Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenService and Maintenance Maintenance and StorageSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Models Identification NumbersCE Identification TAG Markings All ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ground Speed Levers Features & ControlsSeat Adjustment Lever Ignition SwitchHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator diesel model only Voltage IndicatorGeneral Operating Safety OperationChecks Before Starting On the water separator Priming the Fuel SystemTo prime the fuel system Diesel Model OnlyDiesel Model Starting the EngineStopping the Tractor & Engine Gas ModelPushing the Rider by Hand Driving the TractorReverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn To raise the roll bar Attaching a TrailerRaise & Lower the Roll BAR To lower the roll barTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Long Term Storage Longer Than 30 Days Starting After Long Term StorageDiesel Fuel Recommendations Temporary Storage 30 Days Or LessStorage Gas Model Operation Engine Maintenance Regular MaintenanceSafety Items Rider MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Change Interval Every 500 Hours Filter Part Number Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Hydraulic OIL Filter ChangeChange Engine Coolant Clean RADIATOR, Screen & OIL Cooler Check Engine Coolant LevelPressurized System Lubrication GreaseOil Battery Maintenance Cleaning the Battery and CablesANTI-SCALP Deck Casters Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Return Spring Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Neutral Position AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing AdjustmentDeck Leveling Adjustment Deck Lift Spring4 Locations More Pre-Load Suspension AdjustmentTo adjust the spring pre-load Less Pre-LoadBlade Brake Check PTO Clutch AdjustmentBelt Removal & Replacement Pump Drive Belt ReplacementPump Drive Belt Removal PTO Drive Belt Replacement Spindle Drive Belt Removal ReplacementPTO Drive Belt Removal PTO Belt Routing Battery Service Checking Battery VoltageJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Chassis SpecificationsDimensions EngineFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents