Ferris Industries 5901178 manual Neutral Position and Return Spring Adjustment, Neutral Adjustment

Page 44

Troubleshooting, Adjustment & Service

Troubleshooting

NEUTRAL POSITION AND RETURN SPRING ADJUSTMENT

To determine if it is necessary to adjust the neutral position, perform the following steps.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.Move the ground speed control levers in the operating position, pull levers rearward and release.

3.Move the ground speed control levers towards the neutral position. If the levers do not align with the notches in the neutral lock plate, it is necessary to adjust the reverse return bolts (A, Figure 34).

Neutral Position Adjustment

1.Loosen the jam nut (D, Figure 34) locked against the clevis.

2.Turn the reverse return bolt (A) clockwise to adjust handle rearward, counter-clockwise to adjust handle forward.

4.Pull lever rearward and release to check position again. Adjust as necessary to align levers with notches.

It is important to note that after every adjustment of the reverse return bolt, the lever must be pulled rearward and released to properly check the neutral position.

5.Once the lever alignment has been adjusted, lock jam nut against the clevis.

Return Spring Adjustment

After adjusting the neutral position, lock the levers in the neutral position and measure the reverse return spring (B, Figure 34) length. This should be 2-3/8” (6,03 cm) long. If not, hold the reverse return bolt (A) with a wrench while turning the spring position nut (C) until the measurement is achieved.

B

 

A

 

C

D

 

Figure 34. Neutral Spring Return Adjustment

A.Reverse Return Bolt

B.Reverse Return Spring

C.Spring Position Nut

D.Jam Nut

NEUTRAL ADJUSTMENT

If the tractor “creeps” while the ground speed control levers are locked in NEUTRAL, then it may be necessary to adjust the control linkage.

NOTE: Perform this adjustment on a hard, level surface such as a concrete floor. The neutral position MUST be checked and adjusted BEFORE performing a neutral adjustment.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.Loosen the jam nuts (B, Figure 35) and turn the adjustment linkage (A) to adjust. If the machine creeps forward, turn the linkage CLOCKWISE (while standing at the rear of the machine, facing forward), if the machine creeps backward, turn the linkage COUNTER-CLOCKWISE.

3.Lock the jam nuts (B) when neutral is achieved.

NOTE: This adjustment should NOT be performed while the machine is running. It may take several attempts to achieve neutral, depending upon how much the machine creeps.

A

B

B

 

Figure 35. Neutral Adjustment (Left-hand side shown)

A.Control Linkage

B.Jam Nuts

42

www.ferrisindustries.com

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Ferris Industries 5100798 DescriptionModel Number Date Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers CE Identification TAG MarkingsAll Models CE ModelsSafety Decals Safety DecalsSafety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Features & Controls Seat Adjustment LeverIgnition Switch Ground Speed LeversPTO Power Take Off Switch Glow Plug Indicator diesel model onlyVoltage Indicator Hour Meter / Maintenance ReminderChecks Before Starting General Operating SafetyOperation Priming the Fuel System To prime the fuel systemDiesel Model Only On the water separatorStarting the Engine Stopping the Tractor & EngineGas Model Diesel ModelDriving the Tractor Pushing the Rider by HandZero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Attaching a Trailer Raise & Lower the Roll BARTo lower the roll bar To raise the roll barMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingProper Mulching Starting After Long Term Storage Diesel Fuel RecommendationsTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Regular Maintenance Safety ItemsRider Maintenance Engine MaintenanceFuel Filter To add fuelChecking / Adding Fuel Gas Check / ADD Engine OIL Check / Change AIR Filter Check Hydraulic OIL LevelHydraulic OIL Filter Change Change Interval Every 500 Hours Filter Part NumberPressurized System Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustment & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Position and Return Spring Adjustment Neutral AdjustmentNeutral Position Adjustment Return Spring AdjustmentParking Brake Adjustment Mowing Height AdjustmentDeck Lift ROD Timing Adjustment Deck Height Pin Position4 Locations Deck Leveling AdjustmentDeck Lift Spring Suspension Adjustment To adjust the spring pre-loadLess Pre-Load More Pre-LoadPTO Clutch Adjustment Blade Brake CheckPump Drive Belt Removal Belt Removal & ReplacementPump Drive Belt Replacement PTO Drive Belt Removal PTO Drive Belt ReplacementSpindle Drive Belt Removal Replacement PTO Belt Routing Jump Starting with Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Specifications DimensionsEngine ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents