Ferris Industries 5901181, 5901180, 5901178, 5901179 manual PTO Clutch Adjustment, Blade Brake Check

Page 49

Troubleshooting, Adjustment & Service

B

B

 

B

A

 

Figure 47. PTO Clutch Adjustment

A.Adjustment Window (Qty. 3, one shown)

B.Adjustment Nut

PTO CLUTCH ADJUSTMENT

Check the PTO clutch adjustment after the initial 25 hour break-in period and then after every 100 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed.

1.Remove key from ignition switch to prevent the possibility of accidental starting while the PTO is being adjusted.

2.See Figure 47. Note the position of the 3 adjustment windows (A) in the side of the brake plate and the nylock adjustment nuts (B).

3.Insert a .016”-.018” (0,40 - 0,45 mm) feeler gauge

(C) through each window, positioning the gauge between the rotor face and the armature face as shown in Figure 48.

4.Alternately tighten the adjustment nuts (B, Figure 47) until the rotor face and armature face just contacts the gauge.

5.Check the windows for an equal amount of tension when the gauge is inserted and removed, and make any necessary adjustments by tightening or loosening the adjustment nuts.

NOTE: The actual air gap between the rotor and armature may vary even after performing the adjustment procedure. This is due to dimensional variations on component parts, and is an acceptable condition.

6.Check the mower blade stopping time. The mower blades and mower drive belt should come to a complete stop within seven (7) seconds after the electric PTO switch is turned off.

A

B

C

Figure 48. Adjust PTO Clutch

A.Window

B.Adjustment Nut

C. .016”-.018” (0,40 - 0,45 mm) Feeler Gauge

WARNING

To avoid serious injury, perform adjustments only with engine stopped, key removed and tractor on level ground.

Blade Brake Check

Mower blades and mower drive belt should come to a complete stop within seven (7) seconds after electric PTO switch is turned off.

1.With parking brake engaged, PTO disengaged and an operator in the seat, start the engine engine.

2.Have an assistant observe the mower drive belt through the open end of the left-hand arbor cover. Engage the PTO and wait several seconds. Disengage the PTO and check the amount of time it takes for the mower drive belt to stop.

3.If the mower drive belt does not stop within seven

(7) seconds, perform the PTO Clutch Adjustment. If the belt still does not stop within seven (7) seconds, see your dealer.

Troubleshooting

47

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Model Number DescriptionFerris Industries 5100798 Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings Identification NumbersAll Models CE ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Seat Adjustment Lever Features & ControlsIgnition Switch Ground Speed LeversGlow Plug Indicator diesel model only PTO Power Take Off SwitchVoltage Indicator Hour Meter / Maintenance ReminderOperation General Operating SafetyChecks Before Starting To prime the fuel system Priming the Fuel SystemDiesel Model Only On the water separatorStopping the Tractor & Engine Starting the EngineGas Model Diesel ModelPushing the Rider by Hand Driving the TractorSmooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Raise & Lower the Roll BAR Attaching a TrailerTo lower the roll bar To raise the roll barMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Diesel Fuel Recommendations Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Safety Items Regular MaintenanceRider Maintenance Engine MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Check / Change AIR Filter Check Hydraulic OIL Level Check / ADD Engine OILHydraulic OIL Filter Change Change Interval Every 500 Hours Filter Part NumberCheck Engine Coolant Level Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerPressurized System Grease LubricationOil Cleaning the Battery and Cables Battery MaintenanceANTI-SCALP Deck Casters Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Neutral Adjustment Neutral Position and Return Spring AdjustmentNeutral Position Adjustment Return Spring AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing AdjustmentDeck Lift Spring Deck Leveling Adjustment4 Locations To adjust the spring pre-load Suspension AdjustmentLess Pre-Load More Pre-LoadBlade Brake Check PTO Clutch AdjustmentPump Drive Belt Replacement Belt Removal & ReplacementPump Drive Belt Removal Spindle Drive Belt Removal Replacement PTO Drive Belt ReplacementPTO Drive Belt Removal PTO Belt Routing Checking Battery Voltage Battery ServiceJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Dimensions SpecificationsEngine ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents