Ferris Industries 5900626, 5901180, 5901181, 5901178, 5901179, 5900621 Checking / Adding Fuel Gas

Page 34

Maintenance

Regular Maintenance

CHECKING / ADDING FUEL (Gas)

To add fuel:

1.Remove the fuel cap (see A, Figure 13).

2.Fill the tank to the bottom of the filler neck. This will allow for fuel expansion.

NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.

3.Install and hand tighten the fuel cap.

4.Repeat same process for opposite tank.

NOTE: The fuel tanks are tied together through a “tee” in the supply lines. By filling only one tank, the level will balance between the two tanks, effectively having 1/2 tank of fuel for each side.

FUEL FILTER

The fuel filter is located in the fuel line between fuel shut off valve and fuel pump, behind the hydraulic reservoir. If filter is dirty or clogged, replace as follows:

1.Shut off the fuel tank selection valve.

2.Disconnect the negative battery cable.

3.Place a container below the filter to catch spilled fuel.

4.Using a pliers, open and slide hose clamps from fuel filter.

5.Remove hoses from filter.

6.Install new filter in proper flow direction in fuel line.

7.Secure with hose clamps.

8.Reconnect the negative battery cable when finished.

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

Do not remove fuel filter when engine is hot, as spilled gasoline may ignite. DO NOT spread hose clamps further than necessary. Ensure clamps grip hoses firmly over filter after installation.

Do not use gasoline containing METHANOL, gasohol containing more than 10% ethanol, gasoline additives, premium gasoline, or white gas because engine/fuel system damage could result.

32

www.ferrisindustries.com

Image 34
Contents Model Number DescriptionFerris Industries 5100798 Date Purchased Table of Contents Operating Safety Safety Rules & InformationSlope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Children Slope OperationTowed Equipment RIDE-ON Units EmissionsMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt All Models Identification NumbersCE Identification TAG Markings CE ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversVoltage Indicator PTO Power Take Off SwitchGlow Plug Indicator diesel model only Hour Meter / Maintenance ReminderOperation General Operating SafetyChecks Before Starting Diesel Model Only Priming the Fuel SystemTo prime the fuel system On the water separatorGas Model Starting the EngineStopping the Tractor & Engine Diesel ModelDriving the Tractor Pushing the Rider by HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn To lower the roll bar Attaching a TrailerRaise & Lower the Roll BAR To raise the roll barHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingProper Mulching Temporary Storage 30 Days Or Less Starting After Long Term StorageDiesel Fuel Recommendations Long Term Storage Longer Than 30 DaysStorage Gas Model Operation Rider Maintenance Regular MaintenanceSafety Items Engine MaintenanceFuel Filter To add fuelChecking / Adding Fuel Gas Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberCheck Engine Coolant Level Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerPressurized System Grease LubricationOil Cleaning the Battery and Cables Battery MaintenanceANTI-SCALP Deck Casters Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustment & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Neutral Position Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Return Spring AdjustmentParking Brake Adjustment Mowing Height AdjustmentDeck Lift ROD Timing Adjustment Deck Height Pin PositionDeck Lift Spring Deck Leveling Adjustment4 Locations Less Pre-Load Suspension AdjustmentTo adjust the spring pre-load More Pre-LoadPTO Clutch Adjustment Blade Brake CheckPump Drive Belt Replacement Belt Removal & ReplacementPump Drive Belt Removal Spindle Drive Belt Removal Replacement PTO Drive Belt ReplacementPTO Drive Belt Removal PTO Belt Routing Checking Battery Voltage Battery ServiceJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Engine SpecificationsDimensions ChassisFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.