Ferris Industries 5901181, 5901180 Operation, General Operating Safety, Checks Before Starting

Page 19

GENERAL OPERATING SAFETY

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accustomed to the unit.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, tractor and mower free of grass, leaves and excess grease. Do not stop or park tractor over dry leaves, grass or combustible materials.

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

WARNING

Do not load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders.

Operation

CHECKS BEFORE STARTING

•Check that crankcase is filled to full mark on dipstick. See the engine Operators Manual for instructions and oil recommendations.

•Check the radiator fluid level. See engine operator’s manual for instructions.

•Check the hydraulic oil level. Refer to REGULAR MAINTENANCE section.

•Make sure all nuts, bolts, screws and pins are in place and tight.

•Adjust the seat position, and make certain you can reach all controls from the operators position.

•Fill the fuel tanks with fresh fuel. Refer to engine manual for fuel recommendations.

WARNING

Never operate on slopes greater than 17.6 percent (10°) which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm) horizontally.

Select slow ground speed before driving onto a slope. Use extra caution when operating on slopes with a rear-mounted grass catcher.

Mow across the face of slopes, not up and down,use caution when changing directions and DO NOT START OR STOP ON SLOPE.

Operation

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model Number DescriptionFerris Industries 5100798 Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt CE Models Identification NumbersCE Identification TAG Markings All ModelsSafety Decals Safety DecalsSafety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ground Speed Levers Features & ControlsSeat Adjustment Lever Ignition SwitchHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator diesel model only Voltage IndicatorOperation General Operating SafetyChecks Before Starting On the water separator Priming the Fuel SystemTo prime the fuel system Diesel Model OnlyDiesel Model Starting the EngineStopping the Tractor & Engine Gas ModelPushing the Rider by Hand Driving the TractorReverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn To raise the roll bar Attaching a TrailerRaise & Lower the Roll BAR To lower the roll barTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Long Term Storage Longer Than 30 Days Starting After Long Term StorageDiesel Fuel Recommendations Temporary Storage 30 Days Or LessStorage Gas Model Operation Engine Maintenance Regular MaintenanceSafety Items Rider MaintenanceTo add fuel Fuel FilterChecking / Adding Fuel Gas Change Interval Every 500 Hours Filter Part Number Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Hydraulic OIL Filter ChangeCheck Engine Coolant Level Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerPressurized System Grease LubricationOil Cleaning the Battery and Cables Battery MaintenanceANTI-SCALP Deck Casters Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting, Adjustment & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Return Spring Adjustment Neutral Position and Return Spring AdjustmentNeutral Adjustment Neutral Position AdjustmentMowing Height Adjustment Parking Brake AdjustmentDeck Height Pin Position Deck Lift ROD Timing AdjustmentDeck Lift Spring Deck Leveling Adjustment4 Locations More Pre-Load Suspension AdjustmentTo adjust the spring pre-load Less Pre-LoadBlade Brake Check PTO Clutch AdjustmentPump Drive Belt Replacement Belt Removal & ReplacementPump Drive Belt Removal Spindle Drive Belt Removal Replacement PTO Drive Belt ReplacementPTO Drive Belt Removal PTO Belt Routing Checking Battery Voltage Battery ServiceJump Starting with Auxiliary Booster Battery Troubleshooting, Adjustment & Service Chassis SpecificationsDimensions EngineFerris Limited Warranty Belts and Blades

5900621, 5900626, 5901179, 5901178, 5901181 specifications

Ferris Industries, renowned for its innovative approach to outdoor power equipment, has introduced a range of products identified by the model numbers 5900626, 5901179, 5901180, 5901178, and 5900621. These models exemplify the company's commitment to quality and efficiency, catering to both residential and commercial lawn care needs.

The Ferris Industries 5900626 is a stand-out model in the lineup, designed for superior performance and durability. It features a robust engine that ensures reliable operation under various conditions. Equipped with a cutting-edge suspension system, it provides enhanced comfort and stability, allowing users to navigate uneven terrain effortlessly. This model is specifically tailored for those seeking efficiency without compromising on power, making it ideal for medium to large lawns.

Next in the lineup is the 5901179, which is favored for its compact design and versatility. This model is equipped with advanced cutting technology that delivers a clean, precise cut, ensuring a manicured appearance. Its small footprint allows for easy maneuverability in tight spaces, a vital feature for residential landscapers. Moreover, the ergonomic controls enhance the user experience, reducing fatigue during extended use.

The 5901180 model showcases Ferris Industries’ dedication to technological advancement. Featuring an innovative hydrostatic drive system, it provides smooth acceleration and deceleration, allowing for greater control over speed and direction. This model is engineered for those who demand high levels of maneuverability and responsiveness, making it an excellent choice for complex landscaping tasks.

For users prioritizing reliability, the 5901178 model stands out with its heavy-duty construction. Designed to withstand rigorous use, this model can handle challenging landscapes while maintaining performance. The inclusion of maintenance-free components reduces downtime, ensuring that users can focus on their landscaping projects without interruption.

Lastly, the 5900621 model serves as an efficient piece of equipment for commercial users. It combines powerful performance with fuel efficiency, ensuring that operators can complete larger jobs without frequent refueling. The advanced cutting deck technology ensures even grass trimming, enhancing overall lawn aesthetics.

In conclusion, Ferris Industries continues to impress with models 5900626, 5901179, 5901180, 5901178, and 5900621. Each model incorporates features tailored for specific needs, from exceptional cutting performance to unparalleled durability, ensuring that users can achieve optimal results in their lawn care endeavors.
Top Page Image Contents