Husqvarna 216 manual Adjusting the parking brake Rider 213 C, Rider, Adjusting the throttle wire

Page 19

Maintenance

2Check the tension of the steering wires by squeezing them together by the arrows as illustrated. It should be possible to push them together so that the distance between them is half as much, without using unnecessary force.

3If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Do not over tighten the cables; they should only be drawn in towards the steering collar.

Hold the cable, for example using an adjustable wrench, so that it does not twist.

If you only tension one side the steering wheel’s centre position may change.

Check the wire tension on completion of the adjustment as per item 2.

Adjusting the parking brake Rider 213 C, Rider 216

Check that the brake is correctly adjusted by placing the machine on a slight downhill slope with the clutch disengaged and activating the brake.

When the machine does not stand still, the brake should be adjusted according to the following.

1Loosen the locking nuts (1).

2Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

3Tighten the locking nuts (1).

4The brake should be checked again after adjustment

 

!

WARNING! A poorly adjusted brake can

 

result in reduced braking ability.

 

 

 

 

 

Adjusting the parking brake Rider 216 AWD

Check that the parking brake is adjusted correctly by placing the machine on a slope with the front and rear axles disengaged. Apply and lock the parking brake. When the machine does not stand still, the parking brake should be adjusted according to the following.

1 Remove the left-hand wing cover.

1 Loosen the locking nuts (1).

2Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

3Tighten the locking nuts (1).

4The brake should be checked again after adjustment

5Assemble the left-hand wing cover.

!

WARNING! A poorly adjusted parking brake

can result in reduced braking ability.

 

Adjusting the throttle wire

The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached.

1Release the clamping screw that secures the wire casing and set the choke control to maximum choke.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents English Rider 213 C Rider 216 Rider 216 AWDContents Symbols KEY to SymbolsKEY to Symbols Introduction Pre-delivery service Service journalAfter the first 8 hours Location of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Lifting lever for the cutting unit PresentationPresentation Cutting unitRelease lever Rider 213 C, Rider Cutting height adjustment leverSeat FuelingBefore starting DrivingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the RiderStop the engine Cutting tipsOther objects which can be thrown out by the blades Interval in hours MaintenanceMaintenance schedule Maintenance Daily maintenance At least once Before startingChecking and adjusting the steering wires CleaningRemoving of the machine hoods Result in reduced braking ability Adjusting the parking brake Rider 213 C, RiderAdjusting the parking brake Rider 216 AWD Adjusting the throttle wireReplacing the air filter Replacement of fuel filterChecking the fuel pump’s air filter Fuses Check the safety systemChecking the tyre pressure Ignition systemWhen the engine is running. Mind your fingers Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Placing in the service position Service position for the cutting unitChecking the blades Removing the BioClip plugCombi Changing the oil filter LubricationChecking the engine’s oil level Replacing the engine oilRider 216 AWD Lubricating the belt adjusterChecking the transmission oil level General lubricationTroubleshooting schedule Guard ServiceStorage Winter storageTechnical Data Cutting unit Combi EC-declaration of conformity Applies to Europe only Original instructions 1155329-26 ´z+W@¶6a¨ ´z+W@¶6a¨
Top Page Image Contents