Husqvarna 216 Cutting height adjustment lever, Seat, Fueling, Release lever Rider 213 C, Rider

Page 13

PRESENTATION

Cutting height adjustment lever

The cutting height can be adjusted to 10 different positions with the cutting height lever.

Combi-unit 25-75 mm

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

Loosen the handles under the seat and adjust it forwards or backwards to the desired position.

Fueling

The engine runs on unleaded petrol with a minimum octane rating of 85 (not mixed with oil). We recommend the use of biodegradable alkylate petrol. Do not use petrol that contains methanol.

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1“).

WARNING! Petrol is highly inflammable. ! Exercise care and refuel outdoors (see

safety instructions).

IMPORTANT!

Do not use the fuel tank as a support area.

Release lever Rider 213 C, Rider 216

The release control must be pulled out in order for the machine to be moved when the engine is shutoff. Pull the controls to the end positions, do not use an intermediate position.

•Pull out the control to disengage the drive system.

•Push in the control to engage to the drive system.

Release lever Rider 216 AWD

Rider 216 AWD has one control for the front axle and one control for the rear axle.

Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out.

IMPORTANT!

Always drive the machine with both clutch controls pressed in.

Clutch control, rear axle

•Control drawn out, drive system disengaged.

•Control depressed, drive system engaged.

Clutch control, front axle

The control is positioned on the inside of the left front wheel.

•Rear control (pulled out), drive system disengaged.

•Front control (pushed in), drive system engaged.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents English Rider 213 C Rider 216 Rider 216 AWDContents Symbols KEY to SymbolsKEY to Symbols Introduction Pre-delivery service Service journalAfter the first 8 hours Location of the controls What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation PresentationCutting unit Lifting lever for the cutting unitSeat Cutting height adjustment leverFueling Release lever Rider 213 C, RiderBefore starting DrivingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderStop the engine Cutting tipsOther objects which can be thrown out by the blades Maintenance schedule MaintenanceMaintenance Daily maintenance At least once Before starting Interval in hoursChecking and adjusting the steering wires CleaningRemoving of the machine hoods Adjusting the parking brake Rider 216 AWD Adjusting the parking brake Rider 213 C, RiderAdjusting the throttle wire Result in reduced braking abilityReplacing the air filter Replacement of fuel filterChecking the fuel pump’s air filter Checking the tyre pressure Check the safety systemIgnition system FusesWhen the engine is running. Mind your fingers Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Placing in the service position Service position for the cutting unitChecking the blades Removing the BioClip plugCombi Checking the engine’s oil level LubricationReplacing the engine oil Changing the oil filterChecking the transmission oil level Lubricating the belt adjusterGeneral lubrication Rider 216 AWDTroubleshooting schedule Storage ServiceWinter storage GuardTechnical Data Cutting unit Combi EC-declaration of conformity Applies to Europe only Original instructions 1155329-26 ´z+W@¶6a¨ ´z+W@¶6a¨
Top Page Image Contents