Husqvarna 216 Awd, Rider 213 C manual Contents

Page 2

CONTENTS

Contents
CONTENTS
Contents	2
KEY TO SYMBOLS
Symbols	3
INTRODUCTION
Dear Customer,	5
Driving and transport on public roads	5
Towing	5
Use	5
Good service	5
Service journal
Pre-delivery service	6
After the ﬁrst 8 hours	6
WHAT IS WHAT?
Location of the controls	7
SAFETY INSTRUCTIONS
Safety instructions	8
Driving on slopes	9
Children	10
Maintenance	10
Transport	11
PRESENTATION
Presentation	12
Cutting unit	12
Lifting lever for the cutting unit	12
Cutting height adjustment lever	13
Seat	13
Fueling	13
Release lever	13
Release lever	13
Driving
Before starting	14
Start the engine	14
Starting the engine with a weak battery	15
Driving the Rider	15
Cutting tips	16
Stop the engine	16
Maintenance
Maintenance schedule	17
Cleaning	18
Removing of the machine hoods	18
Checking and adjusting the steering wires	18
Adjusting the parking brake	19
Adjusting the parking brake	19
Adjusting the throttle wire	19
Replacing the air ﬁlter	20
Replacement of fuel ﬁlter	20
Checking the fuel pump’s air ﬁlter	20
Checking the tyre pressure	21
Ignition system	21
Fuses	21
Check the safety system	21
Checking the engine’s cooling air intake	21
Checking and adjustment of the cutting unit’s ground
pressure	22

Checking the cutting unit’s parallelism	22
Adjusting the parallelism of the cutting unit	22
Service position for the cutting unit	23
Removing the BioClip plug	24
Checking the blades	24
Lubrication
Checking the engine’s oil level	25
Replacing the engine oil	25
Changing the oil ﬁlter	25
Checking the transmission oil level	26
Lubricating the belt adjuster	26
General lubrication	26
Troubleshooting schedule
Storage
Winter storage	28
Guard	28
Service	28
TECHNICAL DATA
EC-declaration of conformity	31

2 – English

Image 2

Contents Rider 213 C Rider 216 Rider 216 AWD EnglishContents KEY to Symbols SymbolsKEY to Symbols Introduction After the ﬁrst 8 hours Service journalPre-delivery service What is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Cutting unit PresentationPresentation Lifting lever for the cutting unitFueling Cutting height adjustment leverSeat Release lever Rider 213 C, RiderStart the engine DrivingBefore starting Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderOther objects which can be thrown out by the blades Cutting tipsStop the engine Maintenance Daily maintenance At least once Before starting MaintenanceMaintenance schedule Interval in hoursRemoving of the machine hoods CleaningChecking and adjusting the steering wires Adjusting the throttle wire Adjusting the parking brake Rider 213 C, RiderAdjusting the parking brake Rider 216 AWD Result in reduced braking abilityChecking the fuel pump’s air ﬁlter Replacement of fuel ﬁlterReplacing the air ﬁlter Ignition system Check the safety systemChecking the tyre pressure FusesChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitWhen the engine is running. Mind your ﬁngers Service position for the cutting unit Placing in the service positionCombi Removing the BioClip plugChecking the blades Replacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlterGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Rider 216 AWDTroubleshooting schedule Winter storage ServiceStorage GuardTechnical Data Cutting unit Combi EC-declaration of conformity Applies to Europe only 1155329-26 ´z+W@¶6a¨ ´z+W@¶6a¨ Original instructions