Husqvarna Rider 213 C, 216 Awd Service journal, Pre-delivery service, After the ﬁrst 8 hours

Page 6

Service journal

Pre-delivery service

1Charge the battery for 4 hours at max. 3 amp.

2Fit steering wheel, seat and any optional equipment.

3Check and adjust tyre pressure. (60 kPa, 0.6 bar, 9 psi).

4Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb).

Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than front edge.

Adjust the cutting unit’s cutting height setting so that the connection rod is tensed at the lowest cutting height.

5Check that the right amount of oil is in the engine.

6Check that there is oil in the transmission’s oil tank.

7Connect battery.

8Fill with fuel and start engine.

9Check that machine does not move in neutral.

10Check: Forward drive. Reverse drive. Operation of blades. Seat safety switch. Lif lever safety switch.

The safety switch for the hydrostat pedals.

11Check the engine speed See the Technical data section.

12Check the synchronisation between the front and rear wheels. (Only AWD-machines) See the workshop manual.

13Tell customer about:

Needs and beneﬁts of following the service schedule.

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

Range of applications for BioClip. Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

_____________________________________________________________

Date, mileage, stamp, signature

After the ﬁrst 8 hours

1Change engine oil

2Change the oil in the gearbox. (Only AWD- machines)

3Check the synchronisation between the front and rear wheels. (Only AWD-machines)

6 – English

Image 6

Contents Rider 213 C Rider 216 Rider 216 AWD EnglishContents KEY to Symbols SymbolsKEY to Symbols Introduction Service journal Pre-delivery serviceAfter the ﬁrst 8 hours What is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Cutting unit PresentationPresentation Lifting lever for the cutting unitFueling Cutting height adjustment leverSeat Release lever Rider 213 C, RiderDriving Before startingStart the engine Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderCutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance Daily maintenance At least once Before starting MaintenanceMaintenance schedule Interval in hoursCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the throttle wire Adjusting the parking brake Rider 213 C, RiderAdjusting the parking brake Rider 216 AWD Result in reduced braking abilityReplacement of fuel ﬁlter Replacing the air ﬁlterChecking the fuel pump’s air ﬁlter Ignition system Check the safety systemChecking the tyre pressure FusesAdjusting the parallelism of the cutting unit When the engine is running. Mind your ﬁngersChecking the cutting unit’s parallelism Service position for the cutting unit Placing in the service positionRemoving the BioClip plug Checking the bladesCombi Replacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlterGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Rider 216 AWDTroubleshooting schedule Winter storage ServiceStorage GuardTechnical Data Cutting unit Combi EC-declaration of conformity Applies to Europe only 1155329-26 ´z+W@¶6a¨ ´z+W@¶6a¨ Original instructions