Husqvarna Explore Detailed Specs and Features of the Rider 16 and Rider Series

Page 43

TECHNICAL DATA

Dimensions

Length without cutting unit Width without cutting unit Height

Service weight Wheel base Track

Tyre size

Tyre pressure, front & rear

Max. gradient

Engine

Manufacture

Power

Displacement

Fuel

Tank volume

Oil

Oil volume

Start

Electrical system

Type

Battery

Spark plug

Transmission

Manufacture

Oil

Cutting unit

Type

Cutting width

Cutting height

Blade diameter

Noise level

Rider 16

2145 mm

1050 mm

1060 mm

245 kg including cutting unit

855 mm

Front 715 mm, rear 625 mm 16 x 6.50 x 8

60kPa (0.6 kp/cm2)

15°

Briggs & Stratton model 28N707 11.4/15.5 kW/h.p.

465 cm3

Min. 85 octane unleaded 7 litres

SAE 30 or SAE 10W/30 class SF-CC

1.2litres Electric starter

12 V, negative earth

12 V. 24 Ah

Champion CJ8 or J8, electrode gap = 0.7-0.8 mm

Tuff Torq K46

SAE 10W/30, class SF-CC

3-blade unit with side-rear ejection/BioClip

2-blade unit BioClip 900 mm

970 mm, 900mm and 1030 mm (BioClip)

9 pos. 40-90 mm, 45-95 mm (BioClip)

350 mm, 410 mm (Bioclip)

100 dB(A)

When this product is worn out or no longer used it should be returned to the dealer or other appropriate body for recycling.

We reserve the right to change technical specifications without prior notice. Note that no legal claims are valid on the basis of information in this manual.

Use only genuine parts for repairs. The warranty is not valid if non genuine parts are used.

42 – English

Image 43

Contents 101 91 RiderContents II. Slope operation Safety InstructionsSafe operation practices for ride-on mowers General operationIV. Service Dear customer InstructionSerial number Good serviceEngine Transmission Explanation of Symbols Reversing General useDo as follows Driving on slopesChildren MaintenanceBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Lift lever for cutting unit Cutting unitSeat Lever for adjustment of cutting heightFuelling Starting the engine DrivingCold engine Warm engine Driving the machine Cutting tips Release lever Stopping the engineHours Before start 100 MaintenanceMaintenance schedule Daily Maintenance intervalRight-hand fender Dismantling of the machine hoodsEngine hood Front hoodAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Replacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Inspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureFitting the cutting unit Installing BioClipChecking the cutting unit’s parallelism Removing the cutting unit Adjusting the parallelism of the cutting unitReplacing the belts on a BioClip unit Replacing the cutting unit beltsImportant Imformation Placing in service position Service position for cutting unitMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip Check the engine’s oil level LubricationChanging the oil Check the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Problem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage Technical Data EU declaration of conformity Only applies to Europe Work done Date, mileage, stamp, sign Servicejournal RiderPre-delivery service After first 5 hoursServicejournal Servicejournal Servicejournal ´*3-G¶5O¨ English ´*3-G¶5O¨ 2001W03