Husqvarna Rider 16 manual Servicejournal Rider, Pre-delivery service, After first 5 hours

Page 45

		SERVICEJOURNAL RIDER 16

	Work done		Date, mileage, stamp, sign
	Pre-delivery service
	1.	Top up battery with acid and recharge for four hours.
	2.	Fit steering wheel, seat and any optional equipment.
	3.	Adjust cutting unit:
		Adjust the lifting springs (the “weight” of the cutting unit should
		be 12-15 kg). Only applies to BioClip.
		Adjust cutting unit so that rear edge is about 2–4 mm higher
		than front edge.
		Adjust cutting unit height setting so that cutting height limit is 5
		mm above the frame of the unit at the lowest cutting height.
	4.	Check that engine has correct amount of oil.
	5.	Check that the right amount of oil is in the transmission.
	6.	Check and adjust tyre pressure (60 kPa, 0.6 bar).
	7.	Connect battery.
	8.	Fill with fuel and start engine.
	9.	Check that machine does not move in neutral.
	10. Check:
		Forward drive.
		Reverse drive.
		Operation of blades.
		Seat safety switch.
		Lift lever safety switch.
		Safety switch for the hydrostat pedals.
	11. Check engine revs 2 950 rpm.
	12. Tell customer about:		Pre-delivery service carried out.
		Need and benefits of following the service schedule.	No outstanding problems.
		Need and benefits of following the service schedule.
		The need and advantages of leaving the machine for regular	Certified:
		The need and advantages of leaving the machine for regular
		service.
		The effects of maintenance on the machine’s second hand
		value.
		Range of applications for BioClip.
	13. Complete proof of sale, etc.

	After first 5 hours
	1.	Change engine oil.

44 – English

Image 45

Contents 101 91 RiderContents Safe operation practices for ride-on mowers Safety InstructionsGeneral operation II. Slope operationIV. Service Dear customer InstructionGood service Serial numberEngine Transmission Explanation of Symbols Reversing General useDo as follows Driving on slopesChildren MaintenanceBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Throttle and Choke lever Speed limiterParking brake Lift lever for cutting unit Cutting unitLever for adjustment of cutting height SeatFuelling Driving Starting the engineCold engine Warm engine Driving the machine Cutting tips Release lever Stopping the engineMaintenance schedule MaintenanceDaily Maintenance interval Hours Before start 100Engine hood Dismantling of the machine hoodsFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power Replacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterCheck the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Inspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureFitting the cutting unit Installing BioClipChecking the cutting unit’s parallelism Removing the cutting unit Adjusting the parallelism of the cutting unitReplacing the belts on a BioClip unit Replacing the cutting unit beltsImportant Imformation Placing in service position Service position for cutting unitMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip Lubrication Check the engine’s oil levelChanging the oil Lubricating the belt adjuster Check the transmission’s oil levelGeneral lubrication Problem Procedure Trouble Shooting ScheduleService StorageWinter storage Technical Data EU declaration of conformity Only applies to Europe Pre-delivery service Servicejournal RiderAfter first 5 hours Work done Date, mileage, stamp, signServicejournal Servicejournal Servicejournal ´*3-G¶5O¨ English ´*3-G¶5O¨ 2001W03