Zebra Technologies RZ400 manuals
Computer Equipment > Printer
When we buy new device such as Zebra Technologies RZ400 we often through away most of the documentation but the warranty.
Very often issues with Zebra Technologies RZ400 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Printer Zebra Technologies RZ400 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Printer on our side using links below.
Zebra Technologies RZ400 Manual
154 pages 6.66 Mb
1 Z Series®/RZ™ SeriesUser Guide2 © 2011 ZIH CorpProprietary Statement Product Improvements Liability Disclaimer Limitation of Liability Part Number: 79695L-003 3 Declaration of Conformity4 Compliance InformationFCC Compliance Statement FCC Radiation Exposure Statement (for printers with radios or RFID encoders) Canadian DOC Compliance Statement 5 Contents9 About This Document15 Introduction23 Printer Setup39 Operations67 Configuration68 Setup Mode70 Change Password-ProtectedParametersDefault Password Value Disable the Password Protection Feature 71 Print a Configuration Label72 Print a Network Configuration Label73 Standard Control Panel Parameters74 Table 11 • Printer Parameters (Page 2 of 25)Adjust Print Speed 75 Table 11 • Printer Parameters (Page 3 of 25)Adjust the Tear-OffPosition Figure 13 • Tear-OffPosition Adjustment 76 ^LLxxxx77 Table 11 • Printer Parameters (Page 5 of 25)Select Print Method Set Print Width Table 12 • Print Width Ranges and Maximum Values 200 dpi 300 dpi 600 dpi 78 Table 11 • Printer Parameters (Page 6 of 25)Set Maximum Label Length Figure 14 • Label Length 79 Table 11 • Printer Parameters (Page 7 of 25)Set Early Warning for Maintenance EARLY WARNING MAINTENANCE OFF Set Printhead Cleaning Interval for Early Warning WARNING CLEAN PRINTHEAD Reset Printhead Cleaning Counter for Early Warning YES 80 Table 11 • Printer Parameters (Page 8 of 25)Set Printhead Life for Early Warning Default Value: 1,000,000 inches Range: 100 to 1,000,000 inches 2.Press MINUS (-) to move the cursor 3.Press PLUS (+) to increase the value of the digit WARNING REPLACE HEAD Reset Printhead Life Counter for Early Warning To reset the printhead life counter: 2.Did you replace the printhead •If you replaced the printhead, press PLUS (+) to select YES •If you did not replace the printhead, press MINUS (-) to select NO View Non-ResettableCounter View User-ControlledCounter 81 Table 11 • Printer Parameters (Page 9 of 25)Print Counter Readings List Fonts PRINT ZPL only List Bar Codes List Images List Formats 82 Table 11 • Printer Parameters (Page 10 of 25)List Setup List Network Settings List All 83 Table 11 • Printer Parameters (Page 11 of 25)Format Memory Card OPT:MEM ARE YOU SURE FORMAT CARD prompt FORMATTING CARD COMPLETED 84 Table 11 • Printer Parameters (Page 12 of 25)Initialize Flash Memory INITIALIZE FLASH INITIALIZE FLASH prompt INITIALIZING MEMORY COMPLETED Print Sensor Profile 85 Table 11 • Printer Parameters (Page 13 of 25)Calibrate Media and Ribbon Sensor Sensitivity LOAD BACKING 86 Table 11 • Printer Parameters (Page 14 of 25)Language/Parameter Action/Explanation (continued from previous Calibrate Media and Ribbon Sensor Sensitivity (continued) page) c.Close the peel assembly using the peel-offmechanism release lever 4.Leave the printhead open 5.Press PLUS (+) to continue The REMOVE RIBBON prompt displays 1.Remove the ribbon (if used) 2.Close the printhead 3.Press PLUS (+) to continue The message CALIBRATING PLEASE WAIT displays The message displays When calibration is complete, RELOAD ALL displays 2.Reload the ribbon (if used) 3.Close the printhead 4.Press PLUS (+) to continue 87 Table 11 • Printer Parameters (Page 15 of 25)Set Parallel Communications Set Serial Communications Set Baud 88 Table 11 • Printer Parameters (Page 16 of 25)Set Data Bits Set Parity Set Host Handshake 89 Table 11 • Printer Parameters (Page 17 of 25)Set Protocol ZEBRA ACK_NAK ZEBRA DSR/DTR Set Network ID Set Communications Mode 90 Table 11 • Printer Parameters (Page 18 of 25)Set Control Prefix Character Set Format Prefix Character 91 Table 11 • Printer Parameters (Page 19 of 25)Set Delimiter Character Select ZPL Mode 92 Table 11 • Printer Parameters (Page 20 of 25)Select Media Power-UpOption This parameter sets the action of the media when you turn on the printer Default Value (non-RFIDprinters): CALIBRATION CALIBRATION Default Value (RFID printers): FEED Selections: CALIBRATION, SHORT CAL, LENGTH, NO MOTION Calibration Short Cal Length No Motion •Feed—feedsthe labels to the first registration point Select Head Close Option This parameter sets the action of the media when you close the printhead 93 ~JS94 Table 11 • Printer Parameters (Page 22 of 25)Set Reprint Mode See next column View Sensor Settings 95 Table 11 • Printer Parameters (Page 23 of 25)Select Format Convert Select Idle Display 96 Table 11 • Printer Parameters (Page 24 of 25)Set Real-TimeClock (RTC) Date in IDLE DISPLAY Set RTC Time Specify Password Level 97 Table 11 • Printer Parameters (Page 25 of 25)Select the Display Language 98 Additional Control Panel Parameters99 Routine Maintenance111 Troubleshooting139 Specifications147 Index149 international safety organization marks, 33 INVALID HEAD messageINVALID HEAD label length maximum setting, 78 label top printer cannot detect, 127 setting labels did not print, 121 language LCD messages error messages, 113 language selection, 97 Setup mode liability liner removal for Rewind mode, 108 Liner Take-Upmode description, 40 loading media, 43 media path Linerless Peel or Linerless Rewind as print mode options, 40 selecting list settings load factory defaults, 69 loading media, 43 loading ribbon, 58 lubrication media black mark, 35 continuous roll media, 35 fanfold loading media LED setting, 94 non-continuousroll media, 35 ordering perforated RFID “smart” labels, 34 setting media type, 76 specifications tag stock, 34 types of media, 34 web media and ribbon sensor calibration procedure, 85, 86 media compartment cleaning, 105 components media door calibration, 85, 86 print sensor profile network configuration label printing printing using List Network command, 82 network ID setting non-continuousmedia described, 35 setting media type odometer operating conditions, 26 options PAPER OUT message, 114 parallel port characteristics of parallel connection, 28 connector location setting parallel communications, 87 parity setting 151 RIBBON OUT152 THERMISTOR FAULT message cycling with other messages, 114 displayed alone154 Zebra Technologies CorporationZebra Technologies Europe Limited Zebra Technologies Asia Pacific, LLC
Also you can find more Zebra Technologies manuals or manuals for other Computer Equipment.