AMP AMP Device Mode
The ADevice Mode button configures the CR102 to control the AVR360. Pressing this button does not affect the currently selected input on the AVR360.
IMPORTANT: The CR102 must also be in AMP Device
Mode to control the following sources: MCH (multi- channel analogue), AUX, NET (optional network audio), USB, IPOD (for use with the optional Arcam drDock or irDock).
However to control the internal Tuner (AM/FM/DAB (if fitted)) the CR102 must first be in TuN Device Mode (see later).
The functionality of the CR102 is context sensitive for the internal sources and is described in the following table.
PSingle press – Toggles AVR360 power between standby and on in the current zone (zone in which the command is received). Press and hold – Forces all AVR360 zones into standby, regardless of which zone the command was received in.
0…9 | The number keys can be used for source |
| selection (without changing the CR102 |
| Device Mode). Alternatively the Device |
| Mode buttons can also be used with the |
| SHIFT key. |
| 0SAT (satellite) input |
| 2AV input |
| 3TUNER input |
| 4BD input |
| 5disPlay input |
| 6VCR input |
| 7CD input |
| 8AUX (front panel) input |
| 9MCH (multichannel) input |
PHONO | Selects the Display input on the AVR360 |
E(television Audio Return Channel).
RPT | (for iPoD and NET sources) |
r
SModifies many keys (see individual key descriptions below).
AUX | Selects MCH (multichannel) input on the |
HAVR360
SHIFT + Hselects AUX input on the AVR360
NET | Selects iPOD input on the AVR360 |
eSHIFT + eselects network (net) internal input on the AVR360
Navigate menus
OK confirms a setting (equivalent to ‘Enter’ or ‘Select’ on some remote controls)
ShifT + >increases the picture resolution. ShifT + 'turns current zone (in which command is received) on
ShifT + ,turns current zone (in which command is received) off.
MCycles through the available surround and downmix modes.
UDisplays the AVR360 setup menu on the On Screen Display (see page
DCycles through the front panel display’s brightness options
@Toggles the mute function of the AVR360
] [ (track control for iPoD and NET sources) | |
| SHIFT + [Follow Zone1 source. |
| When the command is received in Zone2 |
| the source for that zone follows whatever |
| input source is selected in Zone1 |
- + | Decrease |
| volume |
DIRECT | Stereo direct on/off. Provides a direct |
)analogue path from the analogue inputs to the left and right front outputs. Switches off any surround processing modes and shuts down the DSP circuits for the best stereo sound quality.
EQ | Displays the room EQ settings menu |
$ |
|
EFFECT | (for iPoD and NET sources) |
& |
|
BASS | Calls up a |
(adjust the bass setting for a particular input.
Trim | Brings up the speaker trim menu. |
!Use the B, C, D and E navigation buttons. Press TRIM again to exit the speaker trim menu.
As this is a temporary adjustment, these additional trim levels are reset back to the values set in the Speaker Levels menu when the unit is turned off or the unit is put into standby. These temporary trim levels override the speaker levels found in the setup menu.
sync | Delays may be introduced into the video |
#signal by video processing which causes a mismatch between the audio and video timing. You will notice this by speech sound being out of synchronization with the lip movements in the video.
To compensate for this, you can adjust the lip sync delay. Press the synC button and use the D and E navigation buttons. Press again to exit the lip sync trim menu.
SUB | Brings up a temporary subwoofer trim |
%control. Use the D and E navigation buttons. Press SuB again to exit the sub trim menu.
As this is a temporary adjustment, the sub trim level is reset back to the value set in the Speaker Levels menu when the unit is turned off or the unit is put into standby.
TREBLE | Calls up a |
hadjustinput. the treble setting for a particular
FAV+ | (for iPoD and NET sources) |
u |
|
FAV- | (for iPoD and NET sources) |
t |
|
HOME | (for NET source) |
o |
|
INFO | Cycles through the information displayed |
bon the lower left portion of the front panel display.
iPod commands
The iPod interface is selected by pressing ein AMP Device Mode on the CR102. When connected to an iPod via an optional drDock/irDock, the keys below are used to navigate music files inAMP Device Mode.
Navigate the files on screen.
OK selects/play the highlighted file.
RPT | Toggles random (shuffle) play of the playlist |
ron and off.
SHIFT + rcycles through the repeat options
] [ | Selects the previous/next track in the |
| current playlist |
$Begins or resumes playback at the currently highlighted track
&Togglestrack pause and playback of the current
#Stops playback
