Install the Inner Slides | 8e6 Technologies HL-022-002, HL-002-002

Rack Mount Instructions for SL Servers

Rack Setup Suggestions

•Determine the placement of each component in the rack before you install the rails.

•Install the heaviest server components on the bottom of the rack first, and then work up.

Install the Inner Slides

1.Locate the right inner slide, (the slide that will be used on the right side of chassis when facing the front panel of the chassis).

2.Align the four (4) square holes on the right inner slide against the hooks on the right side of the chassis as show below on the left.

3.Securely attach the slide to the chassis with two M4 flat head screws and repeat the steps 1-3 to install the left inner slide to the left side of the chassis.

Install the Outer Slides

1.Measure the distance from the front rail of the rack to the rear rail of the rack.

2.Attach a short bracket to the rear side of the right outer slide, and a long bracket to the front side of the right outer slide as shown above on the right.

3.Adjust the short and long brackets to the proper distance so that the chassis can snugly fit into the rack.

4.Secure the slides to the cabinet with screws.

5.Repeat steps 1-4 for the left outer slide.

8e6 Enterprise Reporter Quick Start Guide

11

Image 15

8e6 Technologies HL-022-002 Rack Mount Instructions for SL Servers, Install the Inner Slides, Install the Outer Slides

Contents

Guide 8e6 Enterprise Reporter Quick Start Guide Contents Regulatory Specifications and Disclaimers Appendix Scsi Connected Storage DeviceIndex ER Enterprise Reporter Introduction Conventions Used in this Document About this Document Procedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup Precautions Rack Mount Instructions for HL Servers Rack Setup SuggestionsInstall the Inner Rails Install the Outer Rails 8e6 Enterprise Reporter Quick Start Guide Install the Server into the Rack Install the Server into a Telco Rack Install the Inner Slides Install the Outer SlidesRack Mount Instructions for SL Servers Install the Slide Assemblies to the Rack Install the Chassis into the Rack Front of bezel Install the SL or HL Server Bezel Power Supply Precautions Check the Power Supply Server Operation and Maintenance Precautions General Safety Information Electrical Safety Precautions AC Power Cord and Cable Precautions Motherboard Battery Precautions LCD Panel Setup Requirements Setup ProceduresQuick Start Setup Requirements Administrator Console Setup Requirements Serial Console Setup Quick Start Setup ProceduresStorage Device Setup for Attached Storage Units Monitor and Keyboard Setup Diagram of SL chassis front panel, power button at far right HyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide 8e6 Enterprise Reporter Quick Start Guide Quick Start menu screen Login screen Quick Start menu administration menu Log Off, Disconnect the Peripherals System Status screen Console Setup Procedures Preliminary SetupWorkstation Configurations Left Boot Up Process Network Setup Access the InternetLog in to the Administrator Console Network Settings 8e6 Enterprise Reporter Quick Start Guide Regional Setting Time Zone Regional Setting NTP Servers Regional Setting Language Physically Connect the ER to the Network LCD Panel Setup Procedures LCD Menu8e6 menu LAN 1 Link Status Current Patch Level DNS 1 Gateway Host Name Regional Setting Time Zone, date, time Shutdown Reset Admin Console PasswordReboot LCD Options menu Heartbeat BacklightLCD Controls Access the Internet Change User Name and Password, Set Self- Monitoring Enter a User Name and Password Change User Name and Password Set Self-Monitoring Enter the Master Administrator’s E-Mail Address Select 8e6 Enterprise Reporter, and then click Save R3000 Configuration Client Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen ER Client, ER Server Statistics Window LED Indicator Key LED Indicator Color Condition DescriptionSL Unit HL Unit Rear LED Indicators for Hardware Status Monitoring RAID HL and SL Units Models HL-022-002, HL-002-002, SL-002-002 Safety ComplianceDeclaration of the Manufacturer or Importer Electromagnetic Compatibility EMC Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Unit from the Carton Rack Setup Precautions Rack Mount the ServerRack Mount Components Step Step Step Link the ER Unit with the Scsi Connected Device Install the Unit Shut Down, Restart Procedures Shut Down the Storage Device UnitRestart the Storage Device Unit Physical Components Temperature and Ventilation Status Power Supply StatusLED Display Disk Drive Activity Management AlarmDisc Drive Alarm Silence Button Index 8e6 Enterprise Reporter Quick Start Guide