LED Display, Power Supply Status | 8e6 Technologies HL-022-002

Appendix: SAN Installation

LED Display

Temperature and Ventilation Status

When the LED is green, the blowers are operating at an acceptable RPM, and the inter- nal temperature sensors are within acceptable limits.

The LED alternates green and red to indicate a predicted failure of one blower or an alarmingly rapid increase in temperature.

If the LED is red, a blower has failed or the unit is too hot, and an audible alarm will sound.

Power Supply Status

The LED is green if both power supplies are functional.

The LED is red if either power supply has failed, and an audible alarm will sound. In this scenario, an authorized service personnel should examine the LEDs on each power sup- ply module to determine which has failed.

WARNING: Inadvertently removing the functional, surviving power supply will result in system failure and possible data loss.

68	8e6 Enterprise Reporter Quick Start Guide

Image 72

8e6 Technologies HL-022-002, HL-002-002, SL-002-002 LED Display, Temperature and Ventilation Status, Power Supply Status

Contents

Guide 8e6 Enterprise Reporter Quick Start Guide Contents Regulatory Specifications and Disclaimers Appendix Scsi Connected Storage DeviceIndex ER Enterprise Reporter Introduction About this Document Conventions Used in this Document Procedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Setup Precautions Rack Mount the Server Rack Setup Suggestions Install the Inner RailsInstall the Outer Rails Rack Mount Instructions for HL Servers 8e6 Enterprise Reporter Quick Start Guide Install the Server into the Rack Install the Server into a Telco Rack Install the Inner Slides Install the Outer SlidesRack Mount Instructions for SL Servers Install the Slide Assemblies to the Rack Install the Chassis into the Rack Install the SL or HL Server Bezel Front of bezel Check the Power Supply Power Supply Precautions General Safety Information Server Operation and Maintenance Precautions AC Power Cord and Cable Precautions Electrical Safety Precautions Motherboard Battery Precautions Setup Procedures Quick Start Setup RequirementsAdministrator Console Setup Requirements LCD Panel Setup Requirements Quick Start Setup Procedures Storage Device Setup for Attached Storage UnitsMonitor and Keyboard Setup Serial Console Setup Diagram of SL chassis front panel, power button at far right HyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide 8e6 Enterprise Reporter Quick Start Guide Login screen Quick Start menu screen Quick Start menu administration menu System Status screen Log Off, Disconnect the Peripherals Console Setup Procedures Preliminary SetupWorkstation Configurations Left Boot Up Process Network Setup Access the InternetLog in to the Administrator Console Network Settings 8e6 Enterprise Reporter Quick Start Guide Regional Setting Time Zone Regional Setting Language Regional Setting NTP Servers Physically Connect the ER to the Network LCD Panel Setup Procedures LCD Menu8e6 menu Current Patch Level LAN 1 Link Status Gateway DNS 1 Regional Setting Time Zone, date, time Host Name Reset Admin Console Password RebootLCD Options menu Shutdown Heartbeat BacklightLCD Controls Change User Name and Password, Set Self- Monitoring Access the Internet Change User Name and Password Enter a User Name and Password Enter the Master Administrator’s E-Mail Address Set Self-Monitoring R3000 Configuration Select 8e6 Enterprise Reporter, and then click Save Client Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen ER Client, ER Server Statistics Window LED Indicator Key LED Indicator Color Condition DescriptionSL Unit HL Unit Rear LED Indicators for Hardware Status Monitoring HL and SL Units RAID Safety Compliance Declaration of the Manufacturer or ImporterElectromagnetic Compatibility EMC Models HL-022-002, HL-002-002, SL-002-002 Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Unit from the Carton Rack Setup Precautions Rack Mount the ServerRack Mount Components Step Step Step Install the Unit Link the ER Unit with the Scsi Connected Device Shut Down, Restart Procedures Shut Down the Storage Device UnitRestart the Storage Device Unit Physical Components Temperature and Ventilation Status Power Supply StatusLED Display Management Alarm Disc Drive AlarmSilence Button Disk Drive Activity Index 8e6 Enterprise Reporter Quick Start Guide