Left | 8e6 Technologies HL-022-002, HL-002-002, SL-002-002 specs

Link the Workstation to the ER

The procedures outlined in this sub-section require the use of the CAT-5E crossover cable.

A. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 port.

NOTE: When facing the rear of the chassis, the LAN 1 port is the port on the

left.

Portion of SL chassis rear

Portion of HL chassis rear

B.Plug the other end of the CAT-5E crossover cable into the setup workstation’s net- work card.

NOTE: If a CAT-5E coupler was packaged with your unit, this coupler can be used if the crossover cable is not long enough for your setup. Plug one end of the CAT-5E crossover cable into the ER, and the other end into the coupler. Plug a standard CAT-5E cable into the other end of the coupler, and the free end of the standard CAT-5E cable into the setup workstation.

C. Plug the ER into a power source with an appropriate rating.

WARNING: It is strongly suggested you use an uninterruptible power supply.

8e6 Enterprise Reporter Quick Start Guide

29

Image 33

8e6 Technologies HL-022-002, HL-002-002, SL-002-002 quick start Left

Contents

Guide 8e6 Enterprise Reporter Quick Start Guide Contents Regulatory Specifications and Disclaimers Appendix Scsi Connected Storage DeviceIndex ER Enterprise Reporter Introduction Conventions Used in this Document About this Document Procedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup Precautions Install the Inner Rails Rack Setup SuggestionsInstall the Outer Rails Rack Mount Instructions for HL Servers 8e6 Enterprise Reporter Quick Start Guide Install the Server into the Rack Install the Server into a Telco Rack Install the Inner Slides Install the Outer SlidesRack Mount Instructions for SL Servers Install the Slide Assemblies to the Rack Install the Chassis into the Rack Front of bezel Install the SL or HL Server Bezel Power Supply Precautions Check the Power Supply Server Operation and Maintenance Precautions General Safety Information Electrical Safety Precautions AC Power Cord and Cable Precautions Motherboard Battery Precautions Quick Start Setup Requirements Setup ProceduresAdministrator Console Setup Requirements LCD Panel Setup Requirements Storage Device Setup for Attached Storage Units Quick Start Setup ProceduresMonitor and Keyboard Setup Serial Console Setup Diagram of SL chassis front panel, power button at far right HyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide 8e6 Enterprise Reporter Quick Start Guide Quick Start menu screen Login screen Quick Start menu administration menu Log Off, Disconnect the Peripherals System Status screen Console Setup Procedures Preliminary SetupWorkstation Configurations Left Boot Up Process Network Setup Access the InternetLog in to the Administrator Console Network Settings 8e6 Enterprise Reporter Quick Start Guide Regional Setting Time Zone Regional Setting NTP Servers Regional Setting Language Physically Connect the ER to the Network LCD Panel Setup Procedures LCD Menu8e6 menu LAN 1 Link Status Current Patch Level DNS 1 Gateway Host Name Regional Setting Time Zone, date, time Reboot Reset Admin Console PasswordLCD Options menu Shutdown Heartbeat BacklightLCD Controls Access the Internet Change User Name and Password, Set Self- Monitoring Enter a User Name and Password Change User Name and Password Set Self-Monitoring Enter the Master Administrator’s E-Mail Address Select 8e6 Enterprise Reporter, and then click Save R3000 Configuration Client Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen ER Client, ER Server Statistics Window LED Indicator Key LED Indicator Color Condition DescriptionSL Unit HL Unit Rear LED Indicators for Hardware Status Monitoring RAID HL and SL Units Declaration of the Manufacturer or Importer Safety ComplianceElectromagnetic Compatibility EMC Models HL-022-002, HL-002-002, SL-002-002 Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Unit from the Carton Rack Setup Precautions Rack Mount the ServerRack Mount Components Step Step Step Link the ER Unit with the Scsi Connected Device Install the Unit Shut Down, Restart Procedures Shut Down the Storage Device UnitRestart the Storage Device Unit Physical Components Temperature and Ventilation Status Power Supply StatusLED Display Disc Drive Alarm Management AlarmSilence Button Disk Drive Activity Index 8e6 Enterprise Reporter Quick Start Guide