Appendix. Speciﬁcations, Parameter Min Typ Max Unit | Adcom A720

57

Appendix. Speciﬁcations

The A720 series was intended to fulﬁll the speciﬁcation of the ETSI 300 220, Class I, Subclasses a and b, but other national norms are similar to this (for example, the CFR 47, Part 90, Subpart J). Table 6 shows the main operational parameters of the A720 series.

Table 6. Operational Parameters

Parameter	Min	Typ	Max	Unit

Common

Supply	5.0	6.2	10.0	V

Operating Temperature	-30		+70	°C

Relative Humidity	10		99	%

Class Protection		IP65

Data Rate (using the onboard software modem)	1000	150a	2000	bps
Operating Frequency (low band version)b	432		450	MHz
Operating Frequency (high band version)b	450		470	MHz
Frequency Stability (-20 to +60 °C)			±1.5	kHz
Frequency Stability (-30 to +70 °C)			±2.5	kHz

Image 57

Adcom A720, A723 manual Appendix. Speciﬁcations, Parameter Min Typ Max Unit

Contents

ADC N ADC N Contents Contents What are addIT devices? Introduction Installation issues Italics Conventions Chapter Opening the packages Using the Base Station Installing the receiver Installing the base station AddIT Power Supply Installing the power supply Conﬁguring the software Replacing the fuse Using the RTU Shows an addIT RTU Installing the RTU Shows what a typical RTU ﬁeld installation looks like More about the LED tool RTU battery Maintaining and servicing the RTUConﬁguring an addIT RTU in the addVANTAGE software Changing the battery Chapter Chapter Performing Advanced Functions Understanding connectors Receiver connectorDevice series Pins on an I/O Connector Top View RTU connectors Conﬁguring the devices AddIT RTU Power Connector Top View General format of a command Serial communication protocolGeneral format of an answer Using terminal commands Series 1 devicesSET Ownid nnnn SET PMP bl bh SET OwnidSET PMP 63 SET Slot 3600 SET Freq freq step SET Freq 467112500SET Rssi value SET Rssi Querying the actual conﬁguration parameters Cmds Series 2 and 3 devices Freq 433925000 FreqFreq Freq 433925000 25000 Slot PMP 193 cm PMP 65 72193 CM 1 SST Repl DEV Repl 5667 DELDEL Data b1 b2 b3 ... bn Data 5666 12/12/1998Dd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Dn cs Frame 38 description Frame 39 description Data 6367 30/4/1999 Data ImmeRoute Info Fdev Temp = internalTem p Info 255 0 18/4/1999 21511 1.3 0 0 0 91 146 900Anlg Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 6789 Port 7/5/1999 183422 193 RX193 TX #234 BA 6789 B#7851 BA 15190 B VER Blst 30/8/2001 160341VER 1.3 VER 2.0 Notiﬁcations Command line interpreter Returned errors listDevice descriptors and storage handler Real time clock Notiﬁcations Chapter Parameter Min Typ Max Unit Appendix. Speciﬁcations Transmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Credits and Colophon CreditsColophon