Using Device Commands | ADT Security Services Security Manager 2000

USING DEVICE COMMANDS

General

Your system may be set up so that certain lights or other devices can be turned on or off by

Information

using the device command from the touchpad. Ask your installer if this has been done in your

system. If programmed for your system, some devices may activate automatically upon certain

system conditions. In this case, the following commands can be used to override the device

activation. See your installer for a full explanation of this feature.

To activate

ENTER SECURITY CODE THEN PRESS # + 7 + DEVICE NUMBER

devices

+ 7 +

Ê Ê

Ê Ê

Ê Ê

Ê Ê

+

Ê Ê # Ê Ê

Ê Ê

ÊÊ(Security Code)

Example: Ê7Ê Ê2Ê

Ê9Ê Ê6Ê

(Device Number)

then press #, then press 7, then enter the number representing

	the device you wish to activate. See your installer for device numbers assigned for your system.
To deactivate	ENTER SECURITY CODE THEN PRESS # + 8 + DEVICE NUMBER
devices			+ 8 + Ê Ê
	Ê Ê Ê Ê Ê Ê Ê Ê +	Ê Ê # Ê Ê	+ 8 + Ê Ê

ÊÊ(Security Code)

Example: Ê7Ê Ê2Ê Ê9Ê Ê6Ê

(Device Number)

then press #, then 8, then enter the number representing the

device you wish to deactivate. See your installer for device numbers assigned for your system.

Device	Description	Device	Description
1		5
2		6
3		7
4		8

	Ð 23 Ð

Image 23

ADT Security Services Security Manager 2000 Using Device Commands, Enter Security Code then Press # + 7 + Device Number

Contents

Security System About This Manual Table of Contents General Partitioned System System Overview System Overview Single-Button Paging Partition ENTRY/EXIT DelaysGeneral Information Common Zone Operation ENTRY/EXIT DelaysExit Alarms About the Touchpads 10 Ð About the Touchpads 11 Ð Functions of the Touchpads 12 Ð English Display TouchpadCustom English Display Touchpad 13 Ð Using the Ready KeyChecking for Open Zones 14 Ð Arming Perimeter only With Entry Delay onUsing 3 Ê Stay Key 15 Ð Arming Perimeter only With Entry Delay OFFInstant Key 16 Ð Arming ALL Protection With Entry Delay onUsing 2 Ê Êaway Key Use this key when no one will be staying inside 17 Ð Disarming and Silencing AlarmsUsing 1 Ê Êoff Key 18 Ð Using 6 Ê Bypass KeyBypassing Protection Zones 19 Ð Bypassing Protection Zones To turn Chime Mode off Chime ModeUsing 9 Ê Êchime Key To turn Chime Mode on 21 Ð For Manually Activating Silent AND/OR Audible AlarmsUsing Panic Keys Panic Keys 22 Ð Manually Initiating a Fire AlarmVerify this with your installer Enter Security Code then Press # + 8 + Device Number Using Device CommandsEnter Security Code then Press # + 7 + Device Number 24 Ð Paging Feature 25 Ð Security CodesDuress Code Quick Arming Single-Button Security Codes 27 Ð Testing the SystemUsing the Test Key ÊEnter the security code, then press Test key 28 Ð Exit Test Mode 29 Ð Check and Battery DisplaysTrouble Conditions Modem Comm Trouble ConditionsCOMM. Failure System LO BAT Long Rng Trbl Total Power Failure Busy-StandbyDisabled. Call for Service Immediately Open Circuit Maintaining Your System 33 Ð Maintaining Your System 34 Ð Quick Guide to System Functions 35 Ð Summary of AUDIBLE/VISUAL Notifications 36 Ð Summary of AUDIBLE/VISIBLE Notifications 37 Ð UL Notice This is a Grade a Residential System 38 Ð Federal Communications Commission FCC Part 68 Statement 39 Ð Avis 40 Ð Limitations of this Alarm System 41 Ð Limitations of this Alarm System 42 Ð Limited Warranty 43 Ð Installation ÀN7527-6V2Dä