Manuals / Advantech / Computer Equipment / Network Card

Advantech PCI-1784 specifications Hardware Installation, Select the Individual Drivers option

Models: PCI-1784

1 57

Download 57 pages 49.25 Kb

Page 17

Step 3: Select the Individual Drivers option.

Step 4: Select the specific device then just follow the installation instructions step by step to complete your device driver setup.

Fig. 2-2 Different options for Driver Setup

For further information on driver-related issues, an online version of Device Drivers Manual is available by accessing the following path:

Start/Programs/Advantech Device Drivers V2.0/Device Driver Manual

2.3Hardware Installation

Note:

✎Make sure you have installed the driver first before you install the card (please refer to 2.2 Driver Installation)

After the DLL driver installation is completed, you can now go on to install the PCI-1784 card in any PCI slot on your computer. But it is suggested that you should refer to the computer user manual or related documentation if you have any doubt. Please follow the steps below to install the card on your system.

13

Image 17

Advantech PCI-1784 specifications Hardware Installation, Select the Individual Drivers option

Contents

Page Page Contents Appendix D. Operation Encoder Interface FeaturesIntroduction Digital Input and Interrupts CountersFlexible Digital Output function Special Shielded Cable for Noise ReductionBoard ID Applications Installation GuideInstallation Flow Chart Register-level Programming Software OverviewDevice Drivers Programming Tools Device Drivers Programming RoadmapProgramming with Device Drivers Function Library Troubleshooting Device Drivers ErrorWiring Boards AccessoriesWiring Cable Unpacking InstallationPage Setup Screen of Advantech Automation Software Driver InstallationSelect the Individual Drivers option Hardware InstallationPage Device name listed on the Device Manager Board selection Device Setup & Configuration‘Setup’ dialog box Setting Up and configure the deviceOperation dialog box Switch and Jumper Settings Signal ConnectionsOverview Names of Jumpers Function descriptionBoard ID setting SW1 Pin Assignment Signal ConnectionsConnector Signal Description Single ended Outputs Encoder Quadrature encoder inputQuadrature encoder up/down counter input connections Isolated digital output Isolated digital inputEncoder Output Appendix A. SpecificationsTimer General InterruptCounter Latch ADDRESS, Control and Data BUS Appendix B. Block DiagramPage I/O Port Address Map Appendix C. Register Structure and Format+ HEX Table C-1 PCI-1784 register format Part1CH Clock Control Table C-2 PCI-1784 Register for counter 0/1/2/3 mode Counter 0/1/2/3 mode BASE+00/04/08/0CHDI0 Table C-3 PCI-1784 Register for counter 0/1/2/3 latch data Counter 0/1/2/3 latch data BASE+00/04/08/0CHTable C-4 PCI-1784 Register for counter 0/1/2/3 compare data Counter 0/1/2/3 compare data BASE+10/14/18/1CHTable C-5 PCI-1784 Register for interrupt control Interrupt control register BASE+20HTable C-6 PCI-1784 Register for interrupt status Interrupt status register BASE+20HTable C-7 PCI-1784 Register for clock control Clear Interrupt BASE+24HTable C-8 PCI-1784 Register for clear interrupt Table C-9 PCI-1784 Register for software latch Software latch BASE+28HTable C-10 PCI-1784 Board ID data Board ID BASE+28HTable C-11 PCI-1784 Register for reset counter Reset counter BASE+2CHTable C-12 PCI-1784 Register for digital output Digital output BASE+30HTable C-13 PCI-1784 Register for digital input/output Digital input/output BASE+30HPage Quadrature encoder introduction Appendix D. OperationQuadrature input counter mode Mode Maximum input rate 8MHz 4MHz 2MHz 1MHzCounter modes Single-ended vs. differential inputPulse/direction mode Pulse modeDisabled mode Digital noise filterClock frequency Maximum width Latch modeLatch Index latchTimer function Counter reset valueInterrupt function