Applications, Installation Guide | Advantech PCI-1784 specs

Advantech DLL drivers

(included in the companion CD-ROM)PCL-10137H (option)

ADAM-3937 (option)

Personal computer or workstation with a PCI-bus slot (running Windows 2000/95/98/ NT/ME/XP)

1.2Applications

❏Motion control

❏Position sensing, monitoring and measuring

❏Coordinate measuring machines

❏X-Y table monitors

❏Robotics

❏Machine control

1.3Installation Guide

Before you install your PCI-1784 card, please make sure you have the following necessary components:

❏PCI-1784 DA&C card

❏PCI-1784 User’s Manual

❏ Driver software

❏ Wiring cable ❏ Wiring board ❏ Computer

Some other optional components are also available for enhanced operation:

❏Application software ActiveDAQ, GeniDAQ or other third-party

software packages

After you get the necessary components and maybe some of the accessories for enhanced operation of your Multifunction card, you can then begin the Installation procedures. Figure 1-1 on the next page provides a concise flow chart to give users a broad picture of the software and hardware installation procedures:

4

Image 8

Advantech PCI-1784 specifications Applications, Installation Guide

Contents

Page Page Contents Appendix D. Operation Encoder Interface FeaturesIntroduction Counters Digital Input and InterruptsFlexible Digital Output function Special Shielded Cable for Noise Reduction Board ID Installation Guide Applications Installation Flow Chart Register-level Programming Software OverviewDevice Drivers Device Drivers Programming Roadmap Programming Tools Troubleshooting Device Drivers Error Programming with Device Drivers Function Library Wiring Boards AccessoriesWiring Cable Installation UnpackingPage Driver Installation Setup Screen of Advantech Automation Software Hardware Installation Select the Individual Drivers optionPage Device name listed on the Device Manager Device Setup & Configuration Board selection Setting Up and configure the device ‘Setup’ dialog box Operation dialog box Signal Connections Switch and Jumper SettingsOverview Names of Jumpers Function description Board ID setting SW1 Pin Assignment Signal ConnectionsConnector Signal Description Quadrature encoder input Single ended Outputs Encoder Quadrature encoder up/down counter input connections Isolated digital input Isolated digital output Encoder Output Appendix A. SpecificationsTimer General InterruptCounter Latch Appendix B. Block Diagram ADDRESS, Control and Data BUSPage Appendix C. Register Structure and Format I/O Port Address Map Table C-1 PCI-1784 register format Part + HEX 1CH Clock Control Counter 0/1/2/3 mode BASE+00/04/08/0CH Table C-2 PCI-1784 Register for counter 0/1/2/3 mode DI0 Counter 0/1/2/3 latch data BASE+00/04/08/0CH Table C-3 PCI-1784 Register for counter 0/1/2/3 latch data Counter 0/1/2/3 compare data BASE+10/14/18/1CH Table C-4 PCI-1784 Register for counter 0/1/2/3 compare data Interrupt control register BASE+20H Table C-5 PCI-1784 Register for interrupt control Interrupt status register BASE+20H Table C-6 PCI-1784 Register for interrupt status Clear Interrupt BASE+24H Table C-7 PCI-1784 Register for clock control Table C-8 PCI-1784 Register for clear interrupt Software latch BASE+28H Table C-9 PCI-1784 Register for software latch Board ID BASE+28H Table C-10 PCI-1784 Board ID data Reset counter BASE+2CH Table C-11 PCI-1784 Register for reset counter Digital output BASE+30H Table C-12 PCI-1784 Register for digital output Digital input/output BASE+30H Table C-13 PCI-1784 Register for digital input/outputPage Appendix D. Operation Quadrature encoder introduction Mode Maximum input rate 8MHz 4MHz 2MHz 1MHz Quadrature input counter modeCounter modes Single-ended vs. differential input Pulse mode Pulse/direction modeDisabled mode Digital noise filter Latch mode Clock frequency Maximum widthLatch Index latch Counter reset value Timer function Interrupt function