Board ID BASE+28H | Advantech PCI-1784 instruction

C.11 Board ID — BASE+28H

The PCI-1784 offers Board ID register BASE+28H. With correct Board ID settings, user can easily identify and access each card during hardware configuration and software programming.

Table C-10 PCI-1784 Board ID data

	Base Addr.		15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

			31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

										Board ID
	28H	R
	28H	R	0	0	0	0	0	0	0	0	0	0	0	0	BD3	BD2	BD1	BD0

			0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0

BD3 ~ DB0	Board ID
	BD0		LSB of the Board ID
	BD3		MSB of the Board ID

	BD3	BD2		BD1	BD0	Board ID
	1	1		1	1	15
	1	1		1	0	14
	1	1		0	1	13
	1	1		0	0	12
	1	0		1	1	11
	1	0		1	0	10
	1	0		0	1	9
	1	0		0	0	8
	0	1		1	1	7
	0	1		1	0	6
	0	1		0	1	5
	0	1		0	0	4
	0	0		1	1	3
	0	0		1	0	2
	0	0		0	1	1
	0	0		0	0	0

42

Image 46

Advantech specifications Board ID BASE+28H, Table C-10 PCI-1784 Board ID data

Contents

Page Page Contents Appendix D. Operation Introduction FeaturesEncoder Interface Flexible Digital Output function CountersDigital Input and Interrupts Special Shielded Cable for Noise Reduction Board ID Installation Guide Applications Installation Flow Chart Device Drivers Software OverviewRegister-level Programming Device Drivers Programming Roadmap Programming Tools Troubleshooting Device Drivers Error Programming with Device Drivers Function Library Wiring Cable AccessoriesWiring Boards Installation UnpackingPage Driver Installation Setup Screen of Advantech Automation Software Hardware Installation Select the Individual Drivers optionPage Device name listed on the Device Manager Device Setup & Configuration Board selection Setting Up and configure the device ‘Setup’ dialog box Operation dialog box Overview Signal ConnectionsSwitch and Jumper Settings Names of Jumpers Function description Board ID setting SW1 Connector Signal Description Signal ConnectionsPin Assignment Quadrature encoder input Single ended Outputs Encoder Quadrature encoder up/down counter input connections Isolated digital input Isolated digital output Timer Appendix A. SpecificationsEncoder Output Counter Latch InterruptGeneral Appendix B. Block Diagram ADDRESS, Control and Data BUSPage Appendix C. Register Structure and Format I/O Port Address Map Table C-1 PCI-1784 register format Part + HEX 1CH Clock Control Counter 0/1/2/3 mode BASE+00/04/08/0CH Table C-2 PCI-1784 Register for counter 0/1/2/3 mode DI0 Counter 0/1/2/3 latch data BASE+00/04/08/0CH Table C-3 PCI-1784 Register for counter 0/1/2/3 latch data Counter 0/1/2/3 compare data BASE+10/14/18/1CH Table C-4 PCI-1784 Register for counter 0/1/2/3 compare data Interrupt control register BASE+20H Table C-5 PCI-1784 Register for interrupt control Interrupt status register BASE+20H Table C-6 PCI-1784 Register for interrupt status Clear Interrupt BASE+24H Table C-7 PCI-1784 Register for clock control Table C-8 PCI-1784 Register for clear interrupt Software latch BASE+28H Table C-9 PCI-1784 Register for software latch Board ID BASE+28H Table C-10 PCI-1784 Board ID data Reset counter BASE+2CH Table C-11 PCI-1784 Register for reset counter Digital output BASE+30H Table C-12 PCI-1784 Register for digital output Digital input/output BASE+30H Table C-13 PCI-1784 Register for digital input/outputPage Appendix D. Operation Quadrature encoder introduction Counter modes Mode Maximum input rate 8MHz 4MHz 2MHz 1MHzQuadrature input counter mode Single-ended vs. differential input Disabled mode Pulse modePulse/direction mode Digital noise filter Latch Latch modeClock frequency Maximum width Index latch Counter reset value Timer function Interrupt function