Manuals / Agilent Technologies / Power Tools / Welding System

Agilent Technologies E4400-90326 quick start Rear Panel

Models: E4400-90326

1 31

Page 27

ESG Family Signal Generators	Exploring the User Interface
	Rear Panel

Rear Panel

The following pages describe the numbered items shown in the ﬁgure below.

1.	AC Power	The power cord receptacle accepts a three-pronged cable that is
	Receptacle	shipped with the instrument. The line voltage is connected here.
2.	GPIB	The GPIB connector allows communications with compatible
		devices such as external controllers. It is functionally equivalent to
		the AUXILIARY INTERFACE connector.

3.SYMBOL SYNC The TTL/CMOS-compatible SYMBOL SYNC OUT connector

OUT	outputs a symbol synchronization pulse, one data-clock period wide,
	for use in digital modulation applications. This female BNC
	connector is present only on instruments with Options UND or
	UN8. With Option 201 you can select from several different output
	signals for this connector.

Quick Start Guide

2-11

Page 27

Image 27

Agilent Technologies E4400-90326 quick start Rear Panel

Contents

Agilent Technologies ESG Family Signal Generators Part No. E4400-90326Supersedes April Copyright 1999, 2000 Agilent Technologies Contents Getting Started Signal Generator at a Glance Press Preset Creating an FM SignalSetting the Carrier Frequency Setting the Power LevelTurning On Frequency Modulation Setting the FM DeviationSetting the FM Rate RF Output connectorﬁrst level of sweep softkeys is displayed Creating a Step Sweep and a List SweepConﬁguring a Step Sweep StatePress RF ON. The swept RF signal is now available atTurning On Continuous Step Sweep Press ReturnConﬁguring a List Sweep Using Step Sweep Data You triggered the single sweep in the previous step Turning On List Sweep for a Single SweepData Turned offCreating an Instrument State Saving and Recalling an Instrument StateSaving an Instrument State Recalling an Instrument StatePress Save followed by Enter −5 using the numeric keypad and press the dBm softkey Setting Up a Digital Modulation in the GSM FormatConﬁgure Timeslots has become an active softkey Setting Up TimeslotSelecting the Data Format This selects the GSM communications standardPress the Timeslot Type softkey Press the Normal softkey Press the following softkeysThis moves the softkey menu up one level Press Return twice Turning On the GSM Format and the ModulationExploring the User Interface Front Panel Numeric keypad consists of the digit keys 0 through 9, a ConnectorWill be returned to normal instrument operation Associated with the eventDarken in comparison to the text on the display This connector accepts an externally supplied, analogComponent of I/Q modulation. This female BNC connector is Provided only on ESG-D and ESG-DP Series Signal GeneratorsDisplay Frequency and power capabilitiesLCD display provides information on the current instrument To their adjacent keys are located on the right-hand sidePreviously saved in a memory register. You can save up to This hardkey lets you restore any instrument state that youApplications. This female BNC connector is provided only on Softkey or via Scpi command. The maximum input for thisDisplay DisplayThis annunciator appears when a sweep has been initiated Multiple error messages occur, only the most recent messageCan be viewed by pressing Utility Error Info ALC circuit is disabledModulations that you have enabled are modulating the RF Series Signal GeneratorsThis annunciator appears when an error message is placed View and delete error messages using the Utility menuList or step mode RF signal is present at the RF Output connectorS annunciator appears when the signal generator has Generated a service request SRQ over the GpibRear Panel Timebase or 1 ppm high stability timebase Second output is generated every two seconds indicating Output signals for this connectorOption 201 this connector is used for system reset output TTL/CMOS high to TTL/CMOS low edge trigger. With Option UN8BER Sync Loss connector outputs a signal that indicates Q OUT connector outputs the analog, quadrature-phaseBER Meas END connector outputs a signal that indicates Connector is present only on instruments with Option UN7Exploring the User Interface