Manuals / Agilent Technologies / Power Tools / Welding System

Agilent Technologies E4400-90326 quick start Exploring the User Interface

Models: E4400-90326

1 31

Page 31

ESG Family Signal Generators	Exploring the User Interface
	Rear Panel

26.BER DATA IN Use this connector to input the data streams for the bit-error-rate measurements. This female BNC connector is present only on instruments with Option UN7.

27.BER CLK IN Use this connector to input the clock signal for the bit-error-rate measurements. This female BNC connector is present only on instruments with Option UN7.

28.BER GATE IN Use this connector to input the clock gate signal for the

bit-error-rate measurements. The connector can be enabled or disabled by a softkey or an GPIB command. This female BNC connector is present only on instruments with Option UN7.

29.321.4 MHz IN Use this connector to input a downconverted 321.4 MHz GSM signal for base transceiver station (BTS) loopback measurements. This female SMB connector is present only on instruments with Option 300.

Quick Start Guide

2-15

Page 31

Image 31

Agilent Technologies E4400-90326 quick start Exploring the User Interface

Contents

Part No. E4400-90326 Agilent Technologies ESG Family Signal GeneratorsSupersedes April Copyright 1999, 2000 Agilent Technologies Contents Getting Started Signal Generator at a Glance Press Preset Creating an FM SignalSetting the Carrier Frequency Setting the Power LevelTurning On Frequency Modulation Setting the FM DeviationSetting the FM Rate RF Output connectorﬁrst level of sweep softkeys is displayed Creating a Step Sweep and a List SweepConﬁguring a Step Sweep StatePress RF ON. The swept RF signal is now available atTurning On Continuous Step Sweep Press ReturnConﬁguring a List Sweep Using Step Sweep Data You triggered the single sweep in the previous step Turning On List Sweep for a Single SweepData Turned offCreating an Instrument State Saving and Recalling an Instrument StateRecalling an Instrument State Saving an Instrument StatePress Save followed by Enter −5 using the numeric keypad and press the dBm softkey Setting Up a Digital Modulation in the GSM FormatConﬁgure Timeslots has become an active softkey Setting Up TimeslotSelecting the Data Format This selects the GSM communications standardPress the following softkeys Press the Timeslot Type softkey Press the Normal softkeyThis moves the softkey menu up one level Press Return twice Turning On the GSM Format and the ModulationExploring the User Interface Front Panel Numeric keypad consists of the digit keys 0 through 9, a ConnectorWill be returned to normal instrument operation Associated with the eventDarken in comparison to the text on the display This connector accepts an externally supplied, analogComponent of I/Q modulation. This female BNC connector is Provided only on ESG-D and ESG-DP Series Signal GeneratorsDisplay Frequency and power capabilitiesLCD display provides information on the current instrument To their adjacent keys are located on the right-hand sidePreviously saved in a memory register. You can save up to This hardkey lets you restore any instrument state that youApplications. This female BNC connector is provided only on Softkey or via Scpi command. The maximum input for thisDisplay DisplayThis annunciator appears when a sweep has been initiated Multiple error messages occur, only the most recent messageCan be viewed by pressing Utility Error Info ALC circuit is disabledModulations that you have enabled are modulating the RF Series Signal GeneratorsThis annunciator appears when an error message is placed View and delete error messages using the Utility menuList or step mode RF signal is present at the RF Output connectorS annunciator appears when the signal generator has Generated a service request SRQ over the GpibRear Panel Timebase or 1 ppm high stability timebase Second output is generated every two seconds indicating Output signals for this connectorOption 201 this connector is used for system reset output TTL/CMOS high to TTL/CMOS low edge trigger. With Option UN8BER Sync Loss connector outputs a signal that indicates Q OUT connector outputs the analog, quadrature-phaseBER Meas END connector outputs a signal that indicates Connector is present only on instruments with Option UN7Exploring the User Interface