Manuals
/
Allied Telesis
/
Computer Equipment
/
Switch
Allied Telesis
AT-X510-52GTX, AT-X510-28GTX, AT-X510-52GPX, AT-X510-28GSX, AT-X510-28GPX manual Tables
Models:
AT-X510-28GPX
AT-X510-28GSX
AT-X510-52GPX
AT-X510-28GTX
AT-X510-52GTX
1
10
90
90
Download
90 pages
11.79 Kb
7
8
9
10
11
12
13
14
<
>
Troubleshooting
Specs
Install
Speed Duplex Mode Wiring Configuration
Wiring Implementation
Problem 4 The LINK/ACT LED for an SFP or SFP+ transceiver is off
PORT Parameter in the Command Line Interface
The procedures in this chapter are
The default duplex mode setting of Auto-Negotiation is not appropriate for ports connected to network devices that do not support Auto-Negotiation and have a fixed duplex mode. You should disable Auto-Negotiation on those ports and set their duplex modes manually to avoid the possibility of duplex mode mismatches. A switch port using Auto-Negotiation defaults to half- duplex if it detects that the end node is not using Auto-Negotiation, which can result in a mismatch if the end node is operating at a fixed duplex mode of full-duplex
MDI Signal
Page 10
Image 10
Tables
10
Page 9
Page 11
Page 10
Image 10
Page 9
Page 11
Contents
x510 Series
Installation Guide for Stand-alone Switches
Gigabit Ethernet Switches
613-001764 Rev. B
Copyright 2013 Allied Telesis, Inc
Laser Safety
Electrical Safety and Emissions Standards
Electrical Safety EN60950-1 TUV, UL 60950-1 CULUS
This product meets the following standards
Translated Safety Statements
Contents
Installing the Switch on a Table or Desktop
Contents
Chapter 3 Installing the Switch on a Table or in an Equipment Rack
Installing the Switch in an Equipment Rack
Figures
Figures
Tables
Tables
Installation Guide for Virtual Chassis Stacking
Preface
This document uses the following conventions
Document Conventions
Notes provide additional information
Contacting Allied Telesis
x510 Series Installation Guide for Stand-alone Switches
Preface
Chapter
Overview
Installation Guide for Virtual Chassis Stacking
x510 Models 10/100/1000 Mbps Twisted Pair Ports
Features
Power Over Ethernet
SFP Slots
Supports single-port BiDi 1000Base-LX SFP transceivers
LEDs Installation Options MAC Address Table Management Software and
Interfaces Management Methods
Figure 2 on page
Front and Back Panels
Switches
Figure 1. Front Panels of the AT-x510-28GTX and AT-x510-28GPX
x510-52GPX Switches
Figure 2. Front Panels of the AT-x510-28GSX, AT-x510-52GTX, and AT
Figure 4. Back Panel of the AT-x510-28GPX and AT-x510-52GPX
Figure 5 identifies the components in the management panels on the
Management Panel
Series switches
Figure 5. x510 Series Management Panel
Speed Duplex Mode Wiring Configuration
10/100/1000Base-T Twisted Pair Ports
Cable Type
Distance
Cable Requirements Port Pinouts
10Mbps
Powered Device Classes
Power Over Ethernet
PoE Standards
Cable Requirements
Port
Cable Type
1000Mbps
PoE+
Port Prioritization
Wiring Implementation
SFP+ Slots
Cable Type
Stacking SFP+ Slots
Transceiver Model
Distance
eco-friendly Button
LEDs
LEDs for the Twisted Pair Ports
State
Description
State
Description
LEDs for the SFP Slots
SFP Slot LEDs
State
LEDs for the SFP+ Slots
Description
Switch ID LED
LEDs for the Stacking Slots
Figure 10. Switch ID LED
Figure 12. Switch ID LEDs in the Low Power Mode
USB Port
Console Port
Power Supplies
Chapter 1 Overview
“Choosing a Site for the Switch” on page
Beginning the Installation
“Reviewing Safety Precautions” on page
“Unpacking the Switch” on page
Reviewing Safety Precautions
Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts. E4
Risk of explosion if battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions
E37
Choosing a Site for the Switch
Unpacking the Switch
Chapter 2 Beginning the Installation
“Installing the Switch on a Table or Desktop” on page
Installing the Switch on a Table or in an Equipment Rack
The procedures in this chapter are
“Installing the Switch in an Equipment Rack” on page
Installing the Switch on a Table or Desktop
Installing the Switch in an Equipment Rack
Chapter 3 Installing the Switch on a Table or in an Equipment Rack
3. Turn the switch over
Figure 16. Attaching the Equipment Rack Brackets
Figure 17. Attaching the Equipment Rack Brackets Continued
Chapter 3 Installing the Switch on a Table or in an Equipment Rack
“Installing SFP and SFP+ Transceivers” on page
Cabling the Networking Ports
This chapter contains the following procedures
Chapter
Cabling the Twisted Pair Ports
The default duplex mode setting of Auto-Negotiation is not appropriate for ports connected to network devices that do not support Auto-Negotiation and have a fixed duplex mode. You should disable Auto-Negotiation on those ports and set their duplex modes manually to avoid the possibility of duplex mode mismatches. A switch port using Auto-Negotiation defaults to half- duplex if it detects that the end node is not using Auto-Negotiation, which can result in a mismatch if the end node is operating at a fixed duplex mode of full-duplex
Installing SFP and SFP+ Transceivers
Installing SFP Modules in the AT-x510-28GSX Switch
Figure 20. Installing an SFP Transceiver
Figure 22. Positioning the SFP Handle in the Upright Position
Installing SFP and SFP+ Modules
Figure 25. Installing an SFP or SFP+ Transceiver
Figure 27. Positioning the SFP or SFP+ Handle in the Upright Position
Powering On the Switch
Chapter
Powering On the Switch
Monitoring the Initialization Processes
Figure 31. Switch Initialization Messages Continued
Figure 32. Switch Initialization Messages Continued
Configuring the Switch for Stand-alone Operations
Starting a Local Management Session
Figure 33. Connecting the Management Cable to the Console Port
Disabling VCStack
Figure 36. Moving to the Global Configuration Mode
Confirming the Status of the VCStack Feature
Figure 40. Status of a Stacking Slot When VCStack is Disabled
Figure 42. PORT Parameter in the Command Line Interface
Troubleshooting
Chapter
Problem 4 The LINK/ACT LED for an SFP or SFP+ transceiver is off
Problem 6 The switch functions intermittently
Solutions Try the following
Dimensions H x W x D
Technical Specifications
Physical Specifications
Weights
Maximum Power Consumption
Environmental Specifications
Power Specifications
Input Voltages
MDI Signal
Certifications
RJ-45 Twisted Pair Port Pinouts
MDI-X Signal
MDI-X Signal
RJ-45 Style Serial Console Port Pinouts
MDI Signal
Signal
3 Transmit Data 4 Ground 5 Ground 6 Receive Data 7 Looped to pin
Table 20. RJ-45 Style Serial Console Port Pin Signals Continued
Signal
8 Looped to pin
Appendix A Technical Specifications
