Alpine CDE-W235BT Equalizer Presets F-EQ, Turning Loudness On/Off, Setting the Bass Control

5Press and hold AUDIO/SETUP (CDE-W235BT only) for at least 2 seconds or press SETUP (CDE-W233R only) to return to normal mode.

Notes

•Pressing returns to the previous Sound menu mode.

•Pressing and holding for at least 2 seconds will return to normal mode.

•If no operation is performed for 60 seconds, Sound menu mode is cancelled.

Equalizer Presets (F-EQ)

10 typical equalizer settings are preset at the factory for a variety of musical source material.

Setting item: FACTORY EQ

Setting contents:

USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /

ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL

Turning Loudness On/Off

Loudness introduces a special low-and high-frequency emphasis at low listening levels. This compensates for the ear’s decreased sensitivity to bass and treble sound.

Setting item: LOUDNESS

Setting contents:

LOUD OFF (Initial setting) / LOUD ON

Adjusting the Parametric Equalizer Curve (3BAND EQ)

You can modify the Equalizer settings to create a response curve more appealing to your personal taste. The setting of Bass, Mid and Treble can be adjusted in this mode.

Setting item: 3BAND EQ

Further setting items: BASS / MID / TREBLE

Setting the Bass Control

1After selecting BASS from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Bass setting item, and then press ENTER.

WIDTH (Q) CENTER FRQ LEVEL

2Turn the Rotary encoder to select the desired setting value, and then press ENTER.

3Press to return to the previous step.

Setting the Bass Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired bass bandwidth.

WIDE 0.50 MEDIUM 1.00 MEDIUM 1.50 NARROW 2.00

Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency.

Setting the Bass Centre Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired bass centre frequency.

60 (Hz) 80 (Hz) 100 (Hz) 120 (Hz)

Emphasises the displayed bass frequency ranges.

Setting the Bass Level

Turn the Rotary encoder to select the desired bass level (-7~+7)*.

You can emphasise or weaken the bass level.

*The adjustment can also be made by pressing AUDIO/SETUP (CDE-W235BT only) or press AUDIO (CDE-W233R only). Refer to “Adjusting Subwoofer Level/Bass Level/Middle Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat” on page 17.

Setting the Mid Control

1After selecting MID from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Mediant setting item, and then press ENTER.

WIDTH (Q) CENTER FRQ LEVEL

2Turn the Rotary encoder to select the desired setting value, and then press ENTER.

3Press to return to the previous step.

Setting the Mid Bandwidth (WIDTH (Q))

Turn the Rotary encoder to select the desired Mid bandwidth.

WIDE 0.75 MEDIUM 1.00 MEDIUM 1.25 NARROW 1.50

Setting the Mid Centre Frequency (CENTER FRQ)

Turn the Rotary encoder to select the desired Mid centre frequency.

500 (Hz) 1.0k (Hz) 1.5k (Hz) 2.5k (Hz)

Setting the Mid Level

Turn the Rotary encoder to select the desired Mid level (-7 ~ +7)*.

You can emphasise or weaken the Mid level.

*The adjustment can also be made by pressing AUDIO/SETUP (CDE-W235BT only) or press AUDIO (CDE-W233R only). Refer to “Adjusting Subwoofer Level/Bass Level/Middle Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat” on page 17.

18-EN