7When the setting is complete, press and hold MUTE for at least 2 seconds.
The unit returns to the normal mode.
•This adjustment is effective when the setting of the center speaker to SMALL or LARGE in the speaker setup settings.
•This adjustment is ineffective when the speaker is set to CENTER “OFF” in “Setting the Speakers” (page 36).
•When the setting is complete, it is recommended to store the setting contents. For storing, refer to page 43.
Achieving powerful high volume sound
With Dolby Digital, the dynamic range is compressed so that powerful sound can be achieved at regular volume levels. This compression can be canceled to achieve an energetic sound with even greater power, like the sound in a movie theater.
This function works only in the Dolby Digital mode.
1Check that Defeat mode is off (page 21).
2Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3Select the MULTI CH SETUP mode by pressing MUTE repeatedly.
4Select LISTEN MODE by pressing 
or 
, then press MODE.
5Select STANDARD or MAXIMUM by turning the Rotary encoder.
STANDARD: For powerful sound at regular volume levels
MAXIMUM: For powerful sound at high volumes
6When the setting is complete, press and hold MUTE for at least 2 seconds.
The unit returns to the normal mode.
•Keep the volume to a level at which sounds outside the vehicle can still be heard.
•When the setting is complete, it is recommended to store the setting contents. For storing, refer to page 43.
Adjusting the DVD Level
The volume (signal level) for Dolby Digital, Dolby PL II, DTS and PCM modes can be set.
•Avoid stopping, pausing, switching the disc, cueing,
1Check that Defeat mode is off (page 21).
2Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3Select the DVD LEVEL mode by pressing MUTE repeatedly.
4Press MODE to select the mode to be adjusted.
DOLBY D 
PL II 
DTS 
PCM 
DOLBY D
5Adjust the level (LEVEL) by turning the Rotary encoder.
The level can be adjusted in the range of
6Repeat steps 4 and 5 to set each level.
7When the setting is complete, press and hold MUTE for at least 2 seconds.
The unit returns to the normal mode.
•When the setting is complete, it is recommended to store the setting contents. For storing, refer to page 43.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded on two channels to achieve Dolby Pro Logic II surround sound. For
1Check that Defeat mode is off (page 21).
2Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3Select the D PLII/REAR mode by pressing MUTE repeatedly.
4Select the desired mode by pressing 
or 
.
MOVIE MODE:
Suits the stereo TV shows and all programs encoded in Dolby Surround. It improves the sound field directivity to near that of discrete
MUSIC MODE:
Can be used for all stereo music recordings, and provides a wide, deep sound field.
REAR FILL ON:
Depending on the input signals, the sound may only be output from the front speakers. In this case, the “REAR FILL” function can be used to output signals from the rear speakers as well.
OFF: Turns D PLll/REAR function to OFF.
If MUSIC MODE is selected, the center width can be adjusted with the following operations.
This function offers the optimum vocal position by adjusting the center channel position between the center speaker and the L/R speaker. (The adjustments established in “Adjusting the acoustic image” (page 41) are ineffective while this function is activated.)
1After pressing MODE, select MUSIC MODE and turn the Rotary encoder to select CTW CONT ON/OFF.
If ON is selected, press MODE.
If ON is set, you can enjoy the optimum vocal position by distributing the centre channel sound between the center
speaker and L/R speaker.
2After setting to ON, turn the Rotary encoder to adjust the level (LEVEL).
The level can be adjusted between 0 to 7. When the level increases, the center channel position moves from the center speaker position to both sides.
