American Panel AP20BC175-2 guide

AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING

AP20BC175-2 Manual

d.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE LOW AIR TEMPERATURE 28 °F

28 Blinks

e.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HIGH AIR TEMPERATURE 35 °F

35 Blinks

f.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE FOOD TEMPERATURE 40 °F

40 Blinks

g.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HOLDING LOW TEMP. 35 °F

35 Blinks

h.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HOLDING HIGH TEMP. 42 °F

42 Blinks

The display will show:

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE

PROGRAMMING COMPLETE

AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING

After about 2 seconds the display will automatically change to:

The LED for "A" will be "ON".

The LED'S for cycles will be blinking.

i.Press the button. The LED for "HARD" will be steady "ON".

PARAM. PROGRAMMING

AUTOMATIC MODE

CHOOSE

PROGRAMMING CYCLE

j.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE LOW AIR TEMP PART 1

10 °F

10 Blinks

k.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE HIGH AIR TEMP PART 1

20 °F

20 Blinks

18

Image 19

American Panel AP20BC175-2 user manual Automatic Hard Cycle Parameters Programming

Contents

USER’S MANUAL American Panel CorporationREV. C E-mail service@americanpanel.com INDEX INSTALLATION OF REMOTE UNITSINSTALLATION USING THE HURRICHILL TECHNOLOGY STANDARD WARRANTY MAINTENANCE AND CLEANINGWIRING DIAGRAMS PARTS LIST INTRODUCTION CONTROLLER FEATURESOPERATING MODES PC CONNECTION OPTIONAL OPERATING CYCLESADDITIONAL CYCLES PRINTER REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION OF REMOTE UNITSINSTALLATION AT THE SAME LEVEL CONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELS ELECTRICAL AND REFRIGERATION SPECIFICATIONS INSTALLATIONINSTALLATION DIMENSIONS CONNECTION TO THE REMOTE UNIT VERIFYING CORRECT INSTALLATIONCONDENSATE DRAINAGE CONNECTION SPACES AROUND THE CABINET STARTING & TESTING THE UNIT SOFT CHILL CYCLE USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SHOCK FREEZING PANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODEL AP20BC175-2 BLAST CHILLER PROGRAMMING KEYS KEYBOARD KEYSKEY COMBINATIONS ON/OFF & START/STOP 1. INITIAL PROGRAMMING PROGRAMMING The low food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at The high food alarm temperature should be left at The printer baud rate should be left at The P.C. baud rate should be left at AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING 2. PROGRAMMING THE CYCLES AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING q. To change the temperature, press DEFROST CYCLE PARAMETERS PROGRAMMINGp. To change the temperature, press then press MANUAL SOFT CYCLE PARAMETERS PROGRAMMING MANUAL HARD CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATION alternating 2. MANUAL MODE - SOFT CHILL 4. DEFROST CYCLE 3. HARD CHILL CYCLE b. Open the door PRINTER 5. PREPARING AND USING THE PRINTER6. TO CLEAR DATA OPERATING THE PRINTER MAINTENANCELOADING A ROLL OF PAPER REMOVING A ROLL OF PAPER REPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANING CLEANING THE CONDENSER WIRING DIAGRAMSCLEANING THE STORAGE COMPARTMENT AP20BC175-2 Manual AP20BC175-2 Manual AP20BC175-2 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION 5800 S.E. 78th Street, Ocala, Florida STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty AMERICAN PANEL CORP ORDERING PRINTER SUPPLIES RIBBON & PAPER