American Panel AP20BC175-2 specification

MANUAL HARD CYCLE PARAMETERS PROGRAMMING

AP20BC175-2 Manual

MANUAL HARD CYCLE PARAMETERS PROGRAMMING

After about 2 seconds the display will automatically change to:

The LED for "M" will be "ON".

The LED'S for cycles will be blinking.

aa.Press the button. The LED for "HARD" will be steady "ON".

PARAM. PROGRAMMING

MANUAL MODE

CHOOSE

PROGRAMMING CYCLE

bb.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE

LOW AIR TEMP PART 1 10 °F

10 Blinks

cc.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE

HIGH AIR TEMP PART 1 20 °F

20 Blinks

dd.To change the time, press or then

press .

PARAM. PROGRAMMING MANUAL HARD CYCLE TIME 1

H 01:00 MIN

01:00 Blinks

ee.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE

LOW AIR TEMP PART 2 28 °F

28 Blinks

ff.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE

HIGH AIR TEMP PART 2 35 °F

35 Blinks

gg.To change the time, press or then

press .

PARAM. PROGRAMMING MANUAL HARD CYCLE TIME 2

H 01:00 MIN

01:00 Blinks

hh.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE HOLDING LOW TEMP.

35 °F

35 Blinks

ii.To change the temperature, press or

then press .

PARAM. PROGRAMMING MANUAL HARD CYCLE HOLDING HIGH TEMP.

42 °F

42 Blinks

21

Image 22

American Panel AP20BC175-2 user manual Manual Hard Cycle Parameters Programming

Contents

E-mail service@americanpanel.com American Panel CorporationREV. C USER’S MANUAL USING THE HURRICHILL TECHNOLOGY INSTALLATION OF REMOTE UNITSINSTALLATION INDEX PARTS LIST MAINTENANCE AND CLEANINGWIRING DIAGRAMS STANDARD WARRANTY INTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPERATING CYCLESADDITIONAL CYCLES PC CONNECTION OPTIONAL REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION OF REMOTE UNITSINSTALLATION AT THE SAME LEVEL INSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITS DIMENSIONS INSTALLATIONINSTALLATION ELECTRICAL AND REFRIGERATION SPECIFICATIONS CONNECTION TO THE REMOTE UNIT VERIFYING CORRECT INSTALLATIONCONDENSATE DRAINAGE CONNECTION STARTING & TESTING THE UNIT SPACES AROUND THE CABINET SHOCK FREEZING USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SOFT CHILL CYCLE PANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODEL AP20BC175-2 BLAST CHILLER ON/OFF & START/STOP KEYBOARD KEYSKEY COMBINATIONS PROGRAMMING KEYS PROGRAMMING 1. INITIAL PROGRAMMING The high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at The low food alarm temperature should be left at The P.C. baud rate should be left at The printer baud rate should be left at 2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING then press DEFROST CYCLE PARAMETERS PROGRAMMINGp. To change the temperature, press q. To change the temperature, press MANUAL SOFT CYCLE PARAMETERS PROGRAMMING MANUAL HARD CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILL 2. MANUAL MODE - SOFT CHILL alternating 3. HARD CHILL CYCLE 4. DEFROST CYCLE b. Open the door PRINTER 5. PREPARING AND USING THE PRINTER6. TO CLEAR DATA REMOVING A ROLL OF PAPER MAINTENANCELOADING A ROLL OF PAPER OPERATING THE PRINTER MAINTENANCE AND CLEANING REPLACING THE RIBBON WITH PAPER IN THE PRINTER CLEANING THE CONDENSER WIRING DIAGRAMSCLEANING THE STORAGE COMPARTMENT AP20BC175-2 Manual AP20BC175-2 Manual AP20BC175-2 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION AMERICAN PANEL CORP STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty 5800 S.E. 78th Street, Ocala, Florida ORDERING PRINTER SUPPLIES RIBBON & PAPER