Initial Programming, Buttons | American Panel AP24BC250-3 manual

Image 15

American Panel AP24BC250-3 Initial Programming, c. Enter the default password by pressing, in order, the, buttons

Contents

USER’S MANUAL American Panel CorporationREV. E E-mail service@americanpanel.com INSTALLATION AT THE SAME LEVEL CONTROLLER FEATURESINSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS CLEANING THE CONDENSER PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE MAINTENANCE AND CLEANING CONTROLLER FEATURES INTRODUCTIONOPERATING MODES OPERATING CYCLES PRINTER OPTIONALPC CONNECTION OPTIONAL COMPRESSOR INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVEL CONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELS WARNINGS INSTALLATIONINSTALLATION DIMENSIONS CONDENSATE DRAINAGE CONNECTION VERIFYING CORRECT INSTALLATIONELECTRICAL AND REFRIGERATION SPECIFICATIONS CONNECTION TO THE REMOTE UNIT SPACES AROUND THE CABINET STARTING & TESTING THE UNIT SOFT CHILL CYCLE USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SHOCK FREEZING PANNING AND LOADING PANNINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS PROGRAMMING KEYS KEYBOARD KEYSKEY COMBINATIONS ON/OFF & START/STOP 1. INITIAL PROGRAMMING c. Enter the default password by pressing, in order, theIf the entered password is wrong the display will show PROGRAMMING The high air alarm temperature should be left at The low air alarm temperature should be left atThe high food alarm temperature should be left at NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r The low food alarm temperature should be left atThe P.C. baud rate should be left at YES for shock freezers AP24BCF300-3, AP40BCF450-3 2. PROGRAMMING THE CYCLES AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING p. To change the temperature, press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press then press UV LIGHT CYCLE PARAMETERS PROGRAMMING aa. Press DEFROST CYCLE PARAMETERS PROGRAMMINGHEATED PROBE CYCLE PARAMETERS PROGRAMMING The defrost type must be left AIR FLOW hh. To change the temperature, press MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGgg. Press The LED for SOFT will be steady MANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATION 2. MANUAL MODE - SOFT CHILL alternating withalternating 3. HARD CHILL CYCLE a. To perform a UV cycle remove all food, then press 4. SHOCK FREEZE CYCLE5. UV STERILIZATION CYCLE 6. DEFROST CYCLE defrost cycle 7. HEATED FOOD PROBEb. Open the door c. Press the OTE To stop any cycle before it has finished, press START/STOP 8. PREPARING AND USING THE OPTIONAL PRINTER 9. TO CLEAR DATA d. Enter your password, then pressNOTE The optional printer is delivered fully installed PRINTER OPERATING THE PRINTER MAINTENANCELOADING A ROLL OF PAPER REMOVING A ROLL OF PAPER MAINTENANCE AND CLEANING CLEANING THE CONDENSERREPLACING THE RIBBON WITH PAPER IN THE PRINTER DO NOT USE ABRASIVES, SOLVENTS WIRING DIAGRAMSCLEANING COMPARTMENT AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PARTS LIST PART #DESCRIPTION BLAST CHILLERS / SHOCK FREEZERS ONLY STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty AMERICAN PANEL CORP ORDERING PRINTER SUPPLIES RIBBON & PAPER